ykwt500

该程序用于labview信号分析功能，包括小波分析和快速傅里叶变换等(The procedures used for labview signal analysis functions, including wavelet analysis, and fast Fourier transform)

1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。 ⑴ 以NI MyDAQ数据采集卡作为输出接口； ⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形； ⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。 ⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes. ⑴ with NI MyDAQ data acquisition card as output interface ⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel ⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust. ⑷ output waveform can be displayed on the front panel.)

说明：  1）、设计一个程序控制8个外设小灯的点亮方式，要求两种方式A:每个小灯间隔时间T，依次亮，时间T可调，并循环。B：先1.3.5.7.9亮隔时间T，2.4.6.8.10亮，并循环，T可调。 2）、要求主面板与硬件的8个小灯同步。 3）、通过网络在另一台计算机上控制此程序的运行（利用LabVIEW的DateSocket技术）((Network control of virtual instruments 1), design a program to control eight peripheral lights lit the way, the requirements in two ways A: each light interval T, followed by bright, time T adjustable, and circulation. B: first 1.3.5.7.9 bright every time T, 2.4.6.8.10 light, and circulating T-adjustable. 2), requires eight small lights of the main panel and hardware synchronization. 3), through the network control of this program running on another computer (using the LabVIEW DateSocket technology)))

粮情检测系统，适合粮仓粮食的温度测量的Labview程序。(Grain situation detection system for temperature measurement of grain granary Labview program.)

用solidworks建立飞机的三维模型，用labview读取。(Using SolidWorks to build three-dimensional model of the aircraft, with LabVIEW read. )

说明：  基于labview的闹钟设计，完整程序可用(Based labview alarm clock design, complete program)

高级串口读写程序，可以实现串口数据的读写(Advanced Serial literacy program)

电机转速，基于labview。伺服电机控制程序(Motor speed based on LabVIEW. Servo motor control program)

usb 数据采集器，usb批量传输，usb万能调试，usb visa驱动(Usb data collector, usb bulk transfer, usb universal debugging, usb visa drive)

用于labwindows CVI开发环境 可以完成对串口收发数据十六进制和字符型格式的转换(cvi serial port)