Monte-Carlo-simulation-

Simulation program to realize OFDM transmission system(under one path fading)

深入浅出MATLAB 7.X溷合编程 董维国 编着.pdf和适合初学者(MATLAB 7.X blends as easily comprehensible programming Dong Weiguo ed. Pdf and suitable for beginners)

anny边缘检测算子是John F. Canny于 1986 年开发出来的一个多级边缘检测算法。 Canny边缘检测算法： step1:用高斯滤波器平滑图象； step2:用一阶偏导的有限差分来计算梯度的幅值和方向； step3:对梯度幅值进行非极大值抑制； step4:用双阈值算法检测和连接边缘。(anny edge detection operator is John F. Canny developed in 1986 out of a multi-level edge detection algorithm. Canny edge detection algorithm: step1: Gaussian smoothing filter image step2: first-order finite difference to calculate partial derivatives of the magnitude and direction of the gradient step3: the gradient magnitude non-maxima suppression step4: use dual-threshold algorithm for detecting and connecting edges.)

说明：  模拟退火算法来源于固体退火原理，是一种基于概率的算法，将固体加温至充分高，再让其徐徐冷却，加温时，固体内部粒子随温升变为无序状，内能增大，而徐徐冷却时粒子渐趋有序，在每个温度都达到平衡态，最后在常温时达到基态，内能减为最小。(Simulated annealing algorithm is derived from the principle of solid annealing is a kind of algorithm based on probability, high solid heating to fully, then let it slowly cooling, heating, inside the solid particles with the temperature rise to disorder, internal energy increase, and slowly cooling particles become more orderly, and in each temperature to reach the equilibrium state, finally reach the ground state in normal temperature, can reduce to a minimum.)

形成雅克比矩阵的程序，经过验证，可以使用(Jacobian matrix to form the procedure, after verification, you can use)

about various tracking optimization and improve method of tracking.

matlab通信工具箱。里面有多个matlab通信模块的程序。(matlab communication toolbox. There are multiple communication module matlab program.)

说明：   2.wps ：为作业最终的仿真结果与分析 正态分布：.cpp为由C++编写的主程序以获取仿真数据，.txt为存储仿真数据的文档，.m为由matlab根据获取的仿真数据画图的结果，其中1、2、3分别为N（0,1）、N（0,4.26）、N（-2.5,1）的情况 瑞利分布：.cpp为由C++编写的主程序以获取仿真数据，.txt为存储仿真数据的文档，.m为由matlab根据获取的仿真数据画图的结果，其中1、2、3分别为Ray（1）、Ray（0.36）、Ray（3.4）的情况 泊松分布：.cpp为由C++编写的主程序以获取仿真数据，.txt为存储仿真数据的文档，.m为由matlab根据获取的仿真数据画图的结果，其中1、2、3、4分别为Lamda（0.2）、Lamda（1）、Lamda（6）、Lamda（10）的情况 0.m为将三或四种情况画到一副图中并进行仿真结果对比的图像 ((2.wps:) for the job the final simulation results and analysis of the normal distribution:. Cpp written by C++ main program to obtain the simulation data. Txt document for storing simulation data, m grounds matlab drawing according to the simulation data obtained the results, wherein 1, 2, 3 respectively, for the N (0,1), N (0,4.26), N (-2.5,1), of Rayleigh distribution: CPP grounds C++ prepared by the main program to obtain its simulation data, txt for storage simulation data documents, the. m grounds MatLab drawing the results according to the simulation data obtained, wherein 1,2,3 respectively ray (1), ray (0.36), the case of the ray (3.4) poise the loose distribution: cpp grounds written main program C++ to get the simulation data txt simulation data is stored documents, m grounds matlab based on the results of the simulation data obtained drawing, in which 1, 2, 3, 4, respectively 0.m case of Lamda (0.2), Lamda (1), Lamda (6), Lamda (10) of the three or four painting to a graph, )

ejemplos de aplicacion en matlab

本程序旨在计算在整个调节时段的初末水位已知的情况下（水位均为170米），从后往前计算出每个阶段的各个水位到最后阶段的最优发电效益，逐步向前递推找出最大年发电效益，从而找到最优化的路径放入到矩阵LJ中，本程序未考虑防洪限制。(The purpose of this procedure is to calculate the optimal power generation benefit for each stage from the rear to the final stage (the water level is 170m) in the case where the initial water level of the whole adjustment period is known (the water level is 170m), and the maximum annual power generation benefit can be found gradually forward. In order to find the optimized path into the matrix lj, the procedure does not take into account the flood control limitation.)