monituihuosuanfa

几个BOC 信号的分析例程，全球卫星导航系统将普遍采用BOC调制信号作为扩频测距信号，BOC信号自相关函数呈现多个相关峰，传统扩频接收机所用的延迟锁定环（DLL）无法对该信号正确地进行码相位的(Several BOC signal analysis routines, the global satellite navigation system will be widely used BOC modulation signal as a spread spectrum ranging signal, BOC signal auto-correlation function shows a number of correlation peak, the traditional spread-spectrum receiver using delay locked loop (DLL) the signal can not be correctly code phase)

Generates a sample for an arima model

说明：  用ＭＡＴＬＡＢ里边带的ＬＰＣ程序进行参数提取.(MATLAB inside with the LPC parameter extraction procedures.)

地震波转换与ANSYS应用工具及示例。 采用美国加州大学的地震波数据库，然后进行数据库数据的分析，最终得到可以应用到ANSYS中的地震分析输入数据(Conversion of seismic waves with the the ANSYS application of tools and examples. University of California seismic waves database, and then proceed to the analysis of the data from the database, the final seismic analysis of input data can be applied to ANSYS)

系统详细的介绍了matlab软件在各个领域中的应用以及其在科学计算语言中的应用(System is described in detail matlab software applications in various fields as well as their application in scientific computing language)

用matlab仿真模糊控制器，有一定的帮助(fuzzy controller)

这个文件是matlab学习中的一些典型的例子，对于学习matlab的同学很有帮助。(This file is matlab learning some typical examples, very helpful for students to learn matlab.)

Mysmo.mdl 永磁同步电机的主程序，可以实现有速度传感器启动运行，和无速度传感器运行。 SMOmodel.m 改进的滑模观测器模型，实现永磁同步电机反电动势的估算。 PFCDCM0hm5 用的是0.5hm的电感，实现220V交流电变换成400V的直流电，电流断续。 由于是仿真，如果要硬件实现的话，除了需要电压采样外，还需要一个输入电压过零检测 PFCCM320percent98k50 用的是5hm的电感，实现220V交流电变换成320V的直流电，电流连续。功率因数可以达到0.98，用的开关频率为50K PFCCM400percent97k50.mdl 用的是5hm的电感，实现220V交流电变换成400V的直流电，电流连续。功率因数可以达到0.97，用的开关频率为50K (Permanent magnet synchronous motor Mysmo.mdl main program, you can achieve the speed sensor up and running, and speed sensors run. SMOmodel.m improved sliding mode observer model permanent magnet synchronous motor back-EMF estimates. PFCDCM0hm5 with is 0.5hm inductor to achieve 220V AC transform into a 400V DC current is interrupted. As the simulation, hardware implementation, then, in addition to the voltage sampling an input voltage over zero detection PFCCM320percent98k50 the is 5hm inductance to achieve transformation 220V AC 320V DC continuous current. The power factor can reach 0.98, the switching frequency for 50K PFCCM400percent97k50.mdl with is 5hm inductance 220V AC transform 400V DC continuous current. The power factor can reach 0.97, with the switching frequency is 50K)

transmission of image with dssss in AWGN channel

本程序是一个用LSSVM实现简单煤炭数据先拟合程序，用MATLAB编写。(This procedure is a simple to use LSSVM first coal data fitting procedures, prepared by MATLAB.)