SampleQuestions

说明：  谐波小波波程序，包括几个例子，让大家可以对谐波小波处理信号有更加透彻深入的理解和认识。。。(Small wave harmonic procedures, including a few examples, so that we can handle signals of harmonic wavelet a more thorough understanding of and awareness. . .)

均衡器抽头参数中，使用LMS算法确定有限长最优抽头参数(Tap equalizer parameters, the use of finite-length LMS algorithm to determine the optimal tap parameters)

matlab代码，用于计算小波基mallet的程序，对学习小波变换很有用(matlab code used to calculate the wavelet mallet procedures, the study of wavelet transform is useful)

this file simulates a MSK modulation

一个简单的记事本程序，实现了简单的记事功能，用matlab实现(A simple Notepad program to achieve a simple notebook features, using matlab to achieve)

说明：  提出了一种基于MATLAB的无线传感器网络时间同步算法，该算法能实现主从时钟的时间同步。该资源是C语言源代码，在MATLAB上可正常运行。(A time synchronization algorithm of wireless sensor network based on MATLAB is proposed, which can realize the time synchronization of master-slave clock. This resource is C language source code, which can run normally on MATLAB.)

课程设计中首先采用Ising model的思想建立一个二维的模型，然后利用重要性抽样和Monte Carlo方法及其思想模拟铁磁-顺磁相变过程。计算了顺磁物质的能量平均值Ev、热容Cv、磁化强度M及磁化率X的值，进而研究Ev、Cv、M、X与温度T的变化关系并绘制成Ev-T图、Cv-T图、M-T图、X-T图，得出顺磁物质的内能随着温度的升高先增大而后趋于稳定值；热容Cv、磁化率X随着温度的升高先增大后减小；磁化强度M在转变温度Tc处迅速减小为零，找出铁磁相变的转变温度Tc大约为2.35(First of all, curriculum design idea of the Ising model used to establish a two-dimensional model, the importance of sampling and then use Monte Carlo simulation methods and their idea of ferromagnetic- paramagnetic phase transition process. Paramagnetic material calculated average energy Ev, heat capacity Cv, magnetization M and susceptibility X value, and then study Ev, Cv, M, X and temperature changes in the relationship between T and plotted into Ev-T map, Cv- T diagram, MT map, XT maps drawn paramagnetic material can be increased as the temperature increased and then stabilized value heat capacity Cv, magnetic susceptibility X as the temperature increases after the first minus small magnetization M in the transition temperature Tc decreases rapidly to zero Department to identify ferromagnetic phase transition around the transition temperature Tc for 2.35)

Stop-and-wait ARQ is a method used in telecommunications to send information between two connected devices. It ensures that information is not lost due to dropped packets and that packets are received in the correct order. It is the simplest kind of automatic repeat-request (ARQ) method. A stop-and-wait ARQ sender sends one frame at a time it is a special case of the general sliding window protocol with both transmit and receive window sizes equal to 1. After sending each frame, the sender doesn t send any further frames until it receives an acknowledgement (ACK) signal. After receiving a good frame, the receiver sends an ACK. If the ACK does not reach the sender before a certain time, known as the timeout, the sender sends the same frame again.

视频分析方法中的平滑伪Wigner-Ville分布等效于对WVD的结果在时域和频域分别进行一次平滑滤波，有效抑制交叉干扰。(Video analysis methods smoothed pseudo Wigner-Ville distribution is equivalent to the result of the WVD smoothing once were in the time domain and frequency domain, inhibit cross-interference.)

program is to find the user input of action and according to user input it will configure required actions through the serial communication