Channelized-emission-signal

用matlab实现短时能量和过零率的端点检测，并显示波形(using Matlab to achieve short-term energy and zero rate of endpoint detection and waveform display)

Kalman滤波处理运动小球圆心位置，实时测量小球的速度、加速度(Kalman filtering processing ball movement right position )

说明：  基于双耦合Duffing振子的随机相位正弦信号检测 采用双耦合混沌振子阵列实现了随机相位微弱正弦信号的检测，在此基础上，提出了新的检测方法，即利用单个耦合混沌振子，通过临界及周期状态 的变化检测随机相位微弱正弦信号并大致估计信号相位范围，该方法比双耦合混沌振子阵列法简单，更易于实现。(Based on double coupled Duffing oscillators random phase sine signals detected by two coupled chaotic oscillator arrays to achieve a random phase weak sinusoidal signal detection, in this basis, the proposed new detection methods, namely the use of a single coupled chaotic oscillators, through the critical and the cycle random phase state change detection and generally weak sinusoid signal phase estimated the scope of the method than the two-coupled chaotic oscillators array method is simple and more easy to implement.)

Matrices aleatoires : Statistique asymptotique des valeurs propres

two balls collision using matlab

小波包提取滚动轴承故障能量特征的matlab程序，大家只要把采集的滚动轴承振动信号数据放入程序中即可使用，希望对大家有所帮助。(Bearing Fault wavelet packet energy feature extraction matlab program, we just put a rolling bearing vibration signal collected data into the program to use, we want to help.)

采用M2M4信噪比估计算法对QPSK调制解调器的接收端信噪比进行了估计(M2M4 SNR estimation algorithm on the the QPSK modem receiving end signal-to-noise ratio estimated)

基于MATLAB平台的遗传算法工具箱的介绍(MATLAB-based platform for the introduction of genetic algorithm toolbox)

使用说明 1、所有仿真算法按章归类，光盘中的程序名与书中一一对应。 2、将光盘中的仿真程序复制到硬盘MATLAB运行的路径中，便可仿真运行。 3、本书算法在MATLAB 5.3版下运行成功，并适用于其他版本。 4、程序chap1_11.mdl；chap3_2.mdl；chap3_5.mdl；chap6_2.mdl；chap6_4.mdl需要在Matlab6.5下运行，特此说明。 5、假如您对仿真程序有疑问，请及时通过 E-mail 与作者联系。 北京航空航天大学 刘金琨 E-mail 地址： ljk@dept3.buaa.edu.cn或ljk@buaa.edu.cn(Instructions for use, all the simulation algorithms classified by chapter, program name in the CD-ROM and book one-to-one correspondence. 2, the simulation program in the CD-ROM copied to the hard MATLAB running path simulation can be run. Book algorithms in MATLAB 5.3 running successfully, and applies to other versions. 4, the program chap1_11.mdl chap3_2.mdl chap3_5.mdl chap6_2.mdl chap6_4.mdl in Matlab6.5 run is noted. 5, if your simulation program have any questions, please timely contact the author via E-mail. Beijing University of Aeronautics and Astronautics of Liu Jinkun E-mail address: ljk@dept3.buaa.edu.cn or ljk@buaa.edu.cn)

matlab 读取stl文件,输出顶点、面、法向量(matlab read stl file)