convolution

matlab实现图论中的Prim算法,Dijkstra算法,注释清晰，另外附有报告。(matlab realize Prim algorithm of graph theory, Dijkstra algorithm, clear notes and reports.)

用simulink对风电场进行建模分析得到功率以及电流的仿真图(This example uses an initial state vector to start the simulation steady-state. When you make changes to the model (add, delete, rename blocks, etc), the initial state vector needs to be regenerated or disabled, otherwise Simulink signals an error when the simulation is started. To disable the use of initial state vector for this model, go to the Data Import/Export section of the Model Configuration Parameters tool and uncheck the Initial state option under the Load workspace section. To regenerate the initial state vector after a change to the model, follow the instructions given in the initialization file for this model. Type open( init_power_wind_dfig ) at the matlab prompt to view this file.)

LDPC码是目前通信中性能最好的纠错编码之上，这是我在Matlab下编写的LDPC基本解码算法，已经通过调试，大家共同学习(LDPC code is the best communication performance on error-correcting code, this is my prepared in Matlab basic LDPC decoding algorithm has been through debugging, U.S. co-learning)

此程序主要是对振动速度和位移信号的在线采集和处理，功能较为齐全。(This program is mainly for vibration velocity and displacement signal acquisition and processing online, function more complete.)

C Code example with EII

这是用matlab显示K线图的源码,还没有很多的指标，可以继续完善(this is a matlab m file to express stock chart)

说明：  matlab自回归马尔可夫转换模型仿真估计与预测(matlab autoregressive Markov switching model simulation estimates and projections)

任务： 1） 借助MATLAB画出误差性能曲面和误差性能曲面的等值曲线（参考PPT2.1第17页的两幅图）； 2） 写出最陡下降法以及LMS算法的计算公式（取 ）； 3） 用MATLAB产生方差为0.05, 均值为0白噪音S(n)，并画出某次采样得到的波形（即产生任意一个噪声随机序列）； 4） 根据 2）中的公式，并利用 3）中产生的S(n)，在 1）中的误差性能曲面的等值曲线上叠加画出采用最陡下降法以及LMS法时H(n)的在叠代过程中的轨迹曲线（参考PPT2.1第17页的右下图的曲线1和曲线2）。 5）用MATLAB计算并画出LMS法时 随时间n的变化曲线（对应S(n)的某一次的一次实现）和e(n)波形； 注意：某一次实现的结果并不能从统计的角度反映实验的结果 的正确性，为得到具有统计特性的实验结果，可用足够多次的 实验结果的平均值作为实验的结果。用MATLAB计算并画出 采用LMS法时，J(n)的100次实验结果的平均值随时间n的变 化曲线（即 生成随机噪声信号并计算结果，重复执行100次， 求平均结果）。 6）在 1）中的误差性能曲面的等值曲线上，叠加画出采用LMS法得到的100次实验中的H(n)的平均值的轨迹曲线； (Task: 1 ) Draw with MATLAB error performance surface and surface contour error performance curve ( refer PPT2.1 two chart on page 17 ) 2 ) Write the steepest descent method and the LMS algorithm formula ( take ) 3 ) Using MATLAB to generate variance of 0.05 with a mean of 0 white noise S (n), and draw a particular sampling waveform ( ie, any noise generated random sequence ) 4 ) based on 2 ) of the formula , and use 3 ) generated in S (n), in a ) the error performance curves superimposed on the surface contour plot using the steepest descent method and the LMS method when H (n) the iterative process in the trajectory curve ( refer PPT2.1 page 17 bottom right of the curves 1 and 2 ) . 5 ) using MATLAB LMS method is used calculate and draw the curve with time n (corresponding to S (n) of a first implementation of a ) and e (n) waveform Note : in a first implementation of the results are not reflected from a statistical point of view of accuracy of the experimental results ,)

mimo－ofdm系统仿真，matlab源程序(mimo- ofdm system simulation, Matlab source)

RF TRANSCEIVER BLOCKSET IN MATLAB