CS_MRI

自适应门限恒虚警检测的研究，主要是介绍恒虚警的一些基本理论及其仿真方法(Adaptive threshold CFAR detection introduced CFAR some basic theory and simulation method)

电动汽车整车控制策略研究，并且搭建了相关的simulink模型仿真进行验证(Research on vehicle control strategy and Simulation of electric vehicle)

指数平滑法，它提供的预测值是前一期预测值加上前期预测值中产生的误差的修正值。(Exponential smoothing method )

code matlab simulation FDMA

H.S.Park, D-S.Kim, and W.H.Kwon "A Scheduling Method for Network-based Control Systems", IEEE Transaction on Control System Technology, Vol.10, No.3, pp. 318-330, May, 2002 (Simulation Example 1- Matlab Code) (HSPark, DS.Kim, and WHKwon A Scheduling Method for Network-based Control Systems , IEEE Transaction on Control System Technology, Vol.10, No.3, pp. 318-330, May, 2002 (Simulation Example 1- Matlab Code))

采用Fox-Li数值迭代法，对三种激光器腔镜类型下，激光从初始状态到稳定分布的这一过程进行了MATLAB建模仿真。分析了激光器结构参数的变化对光场稳定所需的迭代次数的影响。(Using Fox-Li numerical iterative method, the three types of laser mirrors, the laser from the initial state to the stable distribution of this process modeling and simulation of MATLAB. Analysis of changes in the structural parameters of the laser light field the number of iterations required to stabilize the impact.)

使用M语言编程的PLL程序，可以快速的实现对相位的锁定。(PLL using the M programming language program, you can quickly lock the phase of realization.)

机械齿轮的参数优化，设计一直齿圆柱齿轮传动, 已知其齿数比u= 4, 小轮轴 扭矩T 1= 100N. m, 单向传动, 润滑良好, 非对称布置, 两齿 轮材料 小齿轮40Cr, 调质, 齿面硬度HB= 250~ 280, [ RH ] 1 = 630MPa, [ RF ] 1= 288MPa 大齿轮45 钢, 调质, 齿面硬度 HB= 220~ 250, [ RH ] 2= 550MPa, [ RF ] 2= 204MPa, 取载荷系 数K = 1. 28。(Parameter optimization of the mechanical gear design has been Cylindrical Gear, known gear ratio u = 4, small axle torque T 1 = 100N m, one-way transmission, well-oiled, non-symmetrical arrangement of the materials of the two gears pinion 40Cr quenched and tempered tooth surface hardness HB = 250 ~~ 280 [RH] 1 = 630 MPa [RF] 1 = 288MPa large gear 45 steel, quenched and tempered tooth surface hardness HB = 220 to 250, [RH] = 550MPa , [RF] 2 = 204MPa, to take load factor K = 1 28.)

Pso matlab program，粒子群matlab计算程序，具体看内部注释(Pso matlab program, Particle Swarm matlab calculation program, specifically to see the internal comments)

说明：  K分布仿真的一部分，一部分是斑纹分量 还有是结构分量 两者点乘得到K分布序列 (K distribution part of the simulation, in part, there is a structural component markings component of both the dot distribution sequence obtained K)