udfconfig

A， 单发单收，在发送状态，能够连续发送从0到99的数字； B， 单发单收，在接收状态，能够接收数据，并在数码管上正确地显示出来； C， 单发多收，在AB完成的基础上，接上多个接收设备，能够正确发送和接收 这是从站2的代码(A, single-input single in the sending state, capable of continuously transmitting a number from 0 to 99 B, single-input single in the receiving state, capable of receiving data, and display correctly in the digital tube out C, single overcharged, on the basis of AB completed, connect multiple receiving devices, capable of sending and receiving the correct code from the station which is 2)

说明：  PIC单片机红外线遥控接收解码实例 //芯片配置字，看门狗关，上电延时开，掉电检测关，低压编程关，加密，4M晶体HS振荡(PIC Microcontroller Infrared Remote Control Receiver Decoder instance of// chip configuration word, watchdog off, power-on delay to open, brown-out detection pass, low-voltage programming off, encryption, 4M crystal oscillator HS)

公交自动报站系统的设计，需要用到语音芯片，还有显示器，用单片机设计，protues进行仿真(Automatic stop system bus design, the need to use voice chip, as well as monitors, MCU design, protues simulation)

说明：  通过SSDTHOOK技术实现文件隐藏。。(File hidden by SSDTHOOK technology. .)

VB 开发C51的动态链接库，可以拿来直接用的，(VB-C51 dynamic link library that can be used directly, and)

梦幻古龙2.5D网游全套完整源码 梦幻古龙2.5D网游全套完整源码 梦幻古龙2.5D网游全套完整源码 梦幻古龙2.5D网游全套完整源码(C++ LUA混合而成 )

说明：  MSP430红外解码驱动，占用了一个定时器资源。(MSP430 IR decoding drive, taking up a timer resources.)

基于51单片机的TDC-GP21温度采集程序(Based on 51 single-chip temperature acquisition procedures TDC-GP21)

C8051F060 自带高速AD进行数据采集 可达100兆采样率 并切缓存与片外ram 并把采集数据通过串口发送给PC ( Data Acquisition example for C8051F060 Description: This example illustrates the use of ADC1 and the DMA to acquire and store data. It is intended for use with the C8051F060 target board in the development kit. // This code measures a signal at the AIN0 input with the 16-bit SAR ADC0. // The data is sampled at a rate of 100kHz. ADC output data is transferred to XDATA memory space using the DMA. // // With the EMIF configured for off-chip XRAM access (on the upper ports), this code moves the ADC data to the C8051F060TB target boards s SRAM device. // Once data acquisition is complete, the code then prompts the user to press the P3.7 // button on the target board when ready to receive the data via the UART0 serial port. The TB features an RS-232 transceiver and connector, so the data can be transferred // to a PC via its serial port. // The code is set to acquire up to 32768 samples (for 64kbytes of data). The SRAM device - can accommodate up to 128kbytes, )

51单片机的示波器，所有资料,dajiakuaixia(an Oscilloscope by mini51)