-
Pcm_Image
matlab,把文件解压后放入matlab的默认文件夹里,一般是(C:MATLAB7work)。在matlab主窗口中输入命令ima=imread( C:MATLAB7work1.jpg ),然后输入命令[P,U,iter]=GPAS2(ima,2),即可。绝对好运行(matlab, matlab to unzip the files into the default folder, usually (C: MATLAB7 work). In the matlab main window, type the command ima = imread (' C: MATLAB7 work 1.jpg' ), and then enter the command [P, U, iter] = GPAS2 (ima, 2), can. Definitely a good run)
- 2010-06-25 16:27:56下载
- 积分:1
-
KFCMClust
采用模糊C均值对数据集data聚为cluster_n类(Fuzzy C mean data on the data sets together to cluster_n class)
- 2010-09-03 16:02:40下载
- 积分:1
-
encode
改进后的游程编码,可以继续量化编码转化为二进制数据流,针对一些较为接近的数,通过合适的阈值设定可以近似,从而大大压缩数据流(The improved run-length coding, can continue to quantify the code into binary data stream, for some of the more close to the number set by appropriate threshold can be approximated, thereby greatly compressed data stream)
- 2010-03-04 22:00:10下载
- 积分:1
-
rad_pat
RADAR RADIATION PATTERN for synthetic aperture radar system
- 2012-05-04 03:28:42下载
- 积分:1
-
Space_time_trellis_code
Space Time Trellis Code soure code
- 2009-04-02 13:31:09下载
- 积分:1
-
PAPR(SLM)
PAPR SLM(PAPR SLM)
- 2011-05-06 13:50:53下载
- 积分:1
-
VCPmatlab
本文详细介绍了如何实现VC与Matlab的混合编程,对于进行复杂的运算有很好的用处(This paper describes how the VC and Matlab programming mix, for complex calculations to good use)
- 2013-09-07 11:32:39下载
- 积分:1
-
haofushun10
说明: 属于MATLAB开GUI设计开发的入门参考代码,有注释比较通俗易懂(Belongs to Matlab open GUI design and development of the entry reference code, notes more easy to understand)
- 2020-11-25 09:30:28下载
- 积分:1
-
PID_Increase
增量式PID控制算法Matlab仿真程序
设一被控对象G(s)=50/(0.125s^2+7s),用增量式PID控制算法编写仿真程序(输入分别为单位阶跃、正弦信号,采样时间为1ms,控制器输出限幅:[-5,5],仿真曲线包括系统输出及误差曲线,并加上注释、图例)。(Incremental PID control algorithm Matlab simulation program to set up a controlled object G (s) = 50/(0.125s ^ 2+7s), with incremental PID control algorithm simulation program written (unit step input, respectively, sinusoidal signal sampling time is 1ms, the controller output limiter: [-5,5], including simulation system output and error curve curves, plus notes, legend).)
- 2014-01-09 20:54:10下载
- 积分:1
-
DC-Motor
Simulation for DC Motor selection.
It includes two files, which are DCMotor_Trj.m and DCMotor.mdl.
First of all, you run the DCMotor_Trj.m for generating the reference trajectory.
Then, you open the Simulink file(DCMotor.mdl) and run!
You may change DC Motor parameters.
- 2013-01-10 16:13:12下载
- 积分:1