INS_GPS

为了改善无刷直流电机的调速性能 ,针对普通模糊 P ID速度控制器的缺陷 ,研究了基于变论域思想的自适应模糊 P ID控制器及其在 BLDCM控制系统中的应用。(To improve the performance of brushless DC motor speed, the speed for ordinary fuzzy P ID controller defect of thought based on variable universe adaptive fuzzy P ID controller and its control system BLDCM.)

有关参加全国大学生电子设计竞赛培训的一些情况介绍(Some related to take part in the national undergraduate electronic design contest training was introduced )

约束所有时钟（包括你的设计中特有的时钟）对准确的时序分析结果而言是必不可少的。Quartus II TimeQuest Timing Analyzer为各种各样的时钟配置和典型时钟提供许多SDC命令。(Constraining all clocks, including the clocks unique to your design, is essential for accurate timing analysis results. The Quartus II TimeQuest Timing Analyzer provides many SDC commands for a variety of clock configurations and typical clocks.)

这是我根据英飞凌手册编写的IGBT损耗分析软件，软件显示计算公式，用于损耗评估(This is my according to IGBT loss Infineon manual writing and analysis software, the software shows the calculation formula, used to evaluate the loss )

这是关于现代电力系统优化模型及其相关算法研究的优秀博士论文，希望能对大家有用(This is on the modern power system optimization model and its associated algorithm for outstanding doctoral dissertation, hoping to be useful for all of us)

详细推导了复平面上牛顿迭代法的原理和计算公式，用MATLAB编程实现了牛顿迭代法，得到一些奇异绚丽的分形图形(The complex plane is derived in detail the principle and Newton' s iteration formula, using MATLAB programming Newton' s iterative method, get some strange colorful fractal images)

本书为杨小牛的《软件无线电原理和应用》，供学习软件无线电的同学参考(Yang Mavericks book for the )

同步电机模型的MATLAB仿真,本文针对同步电机中具有代表性的凸极机，再使用MATLAB中用于仿真模拟系统的SIMULINK对系统的各个部分进行封装及连接，系统总体分为电源、abc/dq转换器、电机内部模拟、控制反馈四个主要部分，并为其设计了专用的模块，同时对其中的一系列参数进行了配置。(Synchronous motor model of the MATLAB simulation, this paper, synchronous motor has a salient-pole machine representation, and then use the MATLAB simulation system used for the system SIMULINK package and connect the various parts of the system in general is divided into power, abc/dq converters, motor internal simulation, feedback control of four main parts, and to design a dedicated module, while a series of parameters in which the configuration.)

论文写作中最好的画图软件 解压后，先安装软件，结束时不要直接启动软件，先用破解过的2个exe文件替换安装目录的同名文件，再双击reg文件进行注册即可。(The best essay writing drawing software After decompression, install the software, do not start the software directly to the end, the first two with a cracked exe file to replace the installation directory of the same file, and then double-click the reg file to be registered.)

根据返回舱GNC系统的任务,建立了适用于包括风在内的各种干扰作用下六自由度再入弹道仿真数学模型,为半实物仿真奠定了基础。提出了基于标准轨道的再入制导律,严格推导了再入段总升力方向控制中滚动通道姿态控制信号的形成,并给出了工程应用中简化的方法。开发了综合仿真软件 (err)