lamb_problem

terminal滑膜控制例程，以简单的二阶方程为例，包含了非奇异控制(terminal synovial control routine, a simple second-order equations, for example, contains a non-singular control)

详细介绍了MATLAB的基础，并结合实例讲解了其应用(Details of the basis of MATLAB and explain with examples of its application)

CRectTracker（俗称“橡皮筋”类）是一个非常有意思的类，这是一个详细的的使用说明(CRectTracker (commonly known as the rubber band ) is a very interesting class, this is a detailed instructions for the use of MSWord file)

The model used for creating the reference voltage is shown in Fig. 4. First, photovoltaic output current (Ipv) and output voltage (Vpv) are passed through a first order low pass filter with a magnitude of G = 1 and a time constant of T = 0.01 seconds in order to filter out the high frequency components or harmonics from these signals as shown in Fig. 5 and Fig. 6. The filtered current and voltage signals (Ipv_F and Vpv_F) are then fed into the MPPT control block that uses the Incremental Conductance Tracking Algorithm. An algorithm that is based on the fact the slope of the PV array power curve shown in Fig. 7 is zero at the Maximum Power Point (MPP), positive on the left of the MPP, and negative on the right. The MPP can thus be tracked by comparing the instantaneous conductance (I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):

基于MATLAB的模式识别的贝叶斯决策，处理水环境分类问题，共分为5类，最后得出五类总的识别率。 (Bayesian decision pattern recognition based on MATLAB, the problem of classification of water environment treatment, is divided into 5 categories, finally obtains five kinds of total recognition rate. )

本段代码实现了手动选点的matlab配准，在此代码中只选择了3对控制点，同时从结果可以看出手动选点配准的不精确性，为自动选点配准算法的提出提供了实验依据(This code implements manually selected point matlab registration, in this code to select only the three pairs of control points, and the results can be seen from the point of registration manually selected imprecision, with the choice of site for the proposed automatic registration algorithm provide an experimental basis)

Hough变换用于不同信噪比下微弱信号的检测(Application of Hough transform to weak signal detection under different SNR)

一， GUI界面，proj.m 图片选择窗口，testListBoxlj.m 二,最优化算法 PSO.m POWELL.m 三，互信息尺度 MI.m EMI.m RMI.m HiMI.m GMI.m FPMI.m 四，POWELL.m附属子程序 oneDimSearch.m 五，PSO.m附属子程序 myMI.m 六，配准结果检验程序 restore.m 七， gobad.m对图像进行“平移”和“旋转”(First, GUI interface, proj.m picture selection window, testListBoxlj.m II optimization algorithm PSO.mPOWELL.m three or four MI.mEMI.mRMI.mHiMI.mGMI.mFPMI.m-scale mutual information, POWELL.m subsidiary sub- oneDimSearch.m five procedures, PSO.m subsidiary Subroutine myMI.m six, matching the results of testing procedures restore.m 7, gobad.m images )

matlab code to calculate the LMS algorithm vector

几个关于有限元分析的代码，《结构分析的有限元法与matlab编程》-徐荣桥(Several finite element analysis on the code, " Structural Analysis of the finite element method and matlab programming" - Xu Rong Bridge)