Hamming-code

motor simulation using Simulink software for beginners in drives and motor control

该模型实现了一个通用的OFDM TX和RX，这是不依赖于任何特定的行业标准。该模型的目标是开发和研究不断（不是“突发”）载波同步和定时跟踪方案。该技术纳入然后可以扩展和修改，以标准的具体通讯套件。该模型采用了“收购”技术，它利用了循环前缀相关属性，以赶在试图完成罚款跟踪算法一帧的边界粗略的估计。该模型实现了一个16点64循环前缀的OFDM载波波形。在OFDM符号有16个飞行员，3后卫音（0，带边幅），并使用45 QAM的剩余数据流4。 这包括最新型的衰落信道，误码率计算，并改善控制回路动态。(This model implements a generic OFDM TX and RX, which is not tied to any particular industry standard. The objective of this model is to develop and explore a continuous (not “bursty”) carrier and timing tracking synchronization scheme. The techniques incorporated can then be extended and modified to suite specific communications standards. The model uses an “acquisition” technique that exploits the correlation properties of the cyclic prefix to get a rough estimate of the frame boundary before attempting to accomplish the fine tracking algorithms. The model implements a 64 carrier OFDM waveform with a 16 point cyclic prefix. The OFDM symbol has 16 pilots, 3 guard tones (0 amplitude at band edge) and uses 4 QAM for the 45 remaining data streams. This latest model includes a fading channel, BER computation, and improved control loop dynamics. )

应用SIMULINK搭建适用于风力发电系统的风速模型，包括阵风，自然风等风速类型叠加出符合要求的风速模型，为风力发电系统的仿真提供合理的风速 (Application of SIMULINK to build a wind power generation system is suitable for wind speed model, including gusts, wind speed and other types of natural wind out wind speed superposition model to meet the requirements to provide a reasonable wind speed for the simulation of wind power generation systems)

mainMIMO_OFDMA_2Tx_SER.m: 主程序，设置各种参数 gendata.m: 生成原始信息数据的程序 mod_2Tx_STBC_DFUSC.m：调制程序 gen_SUI_CorrCIR.m: 生成信道冲击响应的程序 get_perfectCE_2x2.m: 生成理想信道估计值的程序 chanSUI_corr_2x2.m: 发送信号通过SUI信道的程序 addAWGN_2x2.m: 添加高斯白噪声的程序 dem_DFUSC_2x2_STBC.m: 接收端解调主程序 ls_freq.m: 频域LS算法 ls_time_2x2.m: 时域LS算法 ML_decision.m: Alamouti最大似然检测算法">

载机使用雷达和红外装置对目标进行跟踪定位，对它们的测量值使用数据融合技术进行处理，使得跟踪结果更精确。(Carrier aircraft using radar and infrared devices on the target for tracking and positioning of their measurements using data fusion technology for processing, so that the tracking results more accurate.)

带通滤波函数，故障诊断时采集振动信号后对信号进行滤波后处理。(The signal is filtered after the signal is collected in the fault diagnosis)

运用music算法识别空间目标，附有注释，可改变方向角，深入浅出，本科毕设程序，绝对好用。( Space target recognition algorithm using music, annotated, can change the direction of the angle, in simple terms, undergraduate established procedures, the absolute ease.)

说明：  filter size image processing

说明：  局部碰磨事故检测代码，通过功率谱检测，例子检测了四种类型的碰磨事故(Partial rubbing incident detection code, through the power spectrum detection, examples of detection of the four types of rub-impact accident)

Matlab函数，实现多个横、纵坐标绘图，同时容纳温度、盐度、密度。(Matlab functions for multiple horizontal and vertical coordinates of the drawing, simultaneously hold temperature, salinity, density.)