Toan

bpsk 数字调制 本程序包括基本编程和仿真，希望对大家有帮助(This procedure bpsk digital modulation including basic programming and simulation, we hope to help)

this is a maltab/sumulink simulation of &a novel adaptive neural control of nonlinear systems with actuator saturation,it simulates the algorithm proposed by slemic in 2004.

MATLAB GUI设计学习手记（第二版）源程序 第6章 本书推荐的学习方法： 1）若您是一个MATLAB初学者，且有充裕的时间来学习GUI设计，您可以从本书的第1章开始循序渐进地学习。 2）若您是一位MATLAB初学者，且时间非常紧迫，建议您先学好第1章，然后依次学习第4章、第5章和第6章，其他章节请根据项目需要有选择性地学习。 3）若您已经掌握了MATLAB的基础语法知识，有一定的MATLAB编程基础，也请浏览一下第1章的内容，尤其是专题分析部分。然后先学习本书第4、5和6章，其他章节请根据项目需要有选择性地学习。 4）若您是一位MATLAB GUI方面的专家或老师，您可以将本书作为一本教学的参考书，本书内容全面、讲解详实、代码精炼，是不可多得的GUI宝典。 (MATLAB GUI design learning Hearts (second edition), the recommended way to learn the source code Chapter 6 of this book: 1) If you are a MATLAB beginners, and there is plenty of time to learn GUI design, you can start from Chapter 1 of the book The step-by-step learning. 2) If you are a MATLAB beginners, and the time is very tight, it is recommended that you first learn to Chapter 1, followed by learning Chapter 4, Chapter 5 and Chapter 6, in other sections based on project needs selective learning . 3) If you have mastered the basic grammar of the MATLAB, the MATLAB Programming Fundamentals, please visit the Chapter 1, in particular thematic analysis section. First learning book chapters 4, 5 and 6, then the other chapters selective learning based on project needs. 4) If you are an expert or teacher of a MATLAB GUI, you can book as a teaching reference books, the book is comprehensive, explain the detailed, refined code, is a rare GUI canon.)

使用MATLAB编写的qdudqz神经网络算法，本程序根据训练好的网络文件DNViuWY预测新的数据文件，得到算法的最差性能和最优性能，并绘制出预测数据和原数据的对比图。调试运行正常。 (Using MATLAB preparedqdudqz neural network algorithm, the program according to the trained network fileDNViuWY anticipating new data files to obtain the best performance and the worst performance of the algorithm, and draw out the comparison chart data and predict the original data. Debugging and running properly. )

说明：  传感器阵列波束优化设计与应用书籍第6章的matlab程序(Chapter 6 matlab program of book Sensor array beam optimization design and application)

关于粒子滤波（PF）的matlab程序，说明了粒子滤波的基本算法。(About particle filter (PF) of matlab program shows the basic particle filter algorithm.)

可求解二维变量矩阵的超松弛迭代方法,因此所求解未知量可为二维矩阵。(It is a SOR solver which can be used to solve the 2D unknowns matrix.)

图像的二维福利叶变换，利用matlab变成实现了二维福利叶变换，代码优化(Fourier transform of the image of two Weifu Li matlab realized with two Weifu Li Fourier Transform code optimization)

多于22导位的EEG信号提取及功率谱分析，归一化处理(EEG selection and power spectrum analysis)

The model used for creating the reference voltage is shown in Fig. 4. First, photovoltaic output current (Ipv) and output voltage (Vpv) are passed through a first order low pass filter with a magnitude of G = 1 and a time constant of T = 0.01 seconds in order to filter out the high frequency components or harmonics from these signals as shown in Fig. 5 and Fig. 6. The filtered current and voltage signals (Ipv_F and Vpv_F) are then fed into the MPPT control block that uses the Incremental Conductance Tracking Algorithm. An algorithm that is based on the fact the slope of the PV array power curve shown in Fig. 7 is zero at the Maximum Power Point (MPP), positive on the left of the MPP, and negative on the right. The MPP can thus be tracked by comparing the instantaneous conductance (I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):