AD420

点阵程序 4片16*16点阵显示程序，可以正显，反显，左右移动。(Dot-matrix program 4 16* 16 dot matrix display program, you can now significantly, anti-marked, about mobile.)

.提供一般的题目选择和控制相关功能函数的运行。 .支持在屏幕上直接调参，对参数具有断电保护，锁定保护的功能。 .未加入ucos操作系统（近年来电赛中还没有必要用到操作系统） .此文件针对stm32f103zet6开发板，提供底层的屏幕显示和操作控制功能，具体比赛要求的功能应自行写成单独的模块加入此文件中即可运行。(1. provides general topic selection and control of the function of the function. 2. supports the direct parameter adjustment on the screen, the power failure protection for the parameters and the function of locking the protection. 3. not added to the UCOS operating system (there is no need to use the operating system in recent caller calls) 4., this document provides the bottom screen display and operation control function for the stm32f103zet6 development board, and the function of specific match request should be written into a separate module by itself.)

电表驱动ATT7022待测试版本，需要的请测试测试。(Watt-hour meter drive ATT7022 to be tested version, need to be tested.)

12864液晶显示屏、画图、显示中文、文字取模软件( 12864 LCD display, drawing, show Chinese characters modulo Software)

最新版的佳能单反相机开发包，国内下载不到哦 Canon Digital EOS SDK ED-SDK v2.11 支持以下相机： EOS-1D Mark III EOS 40D EOS-1Ds Mark III EOS DIGITAL REBEL Xsi/450D/ Kiss X2 EOS DIGITAL REBEL XS/ 1000D/ KISS F EOS 50D EOS 5D Mark II EOS Kiss X3/EOS REBEL T1i /EOS 500D EOS 7D EOS-1D Mark IV EOS Kiss X4/EOS REBEL T2i /EOS 550D EOS 60D EOS Kiss X5/EOS REBEL T3i /EOS 600D EOS Kiss X50/EOS REBEL T3 /EOS 1100D EOS-1D X EOS 5D MarkIII EOS 60Da EOS 650D (The latest version of Canon SLR camera development kits, domestic not download Oh Canon Digital EOS SDK ED-SDK v2.11 supports the following cameras: EOS-1D Mark III EOS 40D EOS-1Ds Mark III EOS DIGITAL REBEL Xsi/450D/Kiss X2 EOS DIGITAL REBEL XS/1000D/KISS F EOS 50D EOS 5D Mark II EOS Kiss X3/EOS REBEL T1i/EOS 500D EOS 7D EOS-1D Mark IV EOS Kiss X4/EOS REBEL T2i/EOS 550D EOS 60D EOS Kiss X5/EOS REBEL T3i/EOS 600D EOS Kiss X50/EOS REBEL T3/EOS 1100D EOS-1D X EOS 5D MarkIII EOS 60Da EOS 650D)

触摸芯片 XW09A驱动 可以直接拷来使用(Touch Chip XW09A Driver Can be directly copied to use)

大多数自行车速度表工作通过使用霍尔效应传感器固定在自行车前叉。磁铁是附加到前轮上的辐条之一,它将与霍尔效应开关一次革命的车轮。速度计监测传感器计数轮革命。如果知道车轮的直径,距离可以很容易地计算如果你知道有多少革命的车轮。此外,如果时间完成革命,平均速度也可以计算出来。 对于这个问题,您将编写一个程序来确定总距离(英里)和平均速度(英里每小时)考虑到车轮直径,革命的数量和总时间的旅行。你可以假定前轮从未离开地面,并没有下滑或打滑。(Most bicycle speedometers work by using a Hall Effect sensor fastened to the front fork of the bicycle. A magnet is attached to one of the spokes on the front wheel so that it will line up with the Hall Effect switch once per revolution of the wheel. The speedometer monitors the sensor to count wheel revolutions. If the diameter of the wheel is known, the distance traveled can be easily be calculated if you know how many revolutions the wheel has made. In addition, if the time it takes to complete the revolutions is known, the average speed can also be calculated. For this problem, you will write a program to determine the total distance traveled (in miles) and the average speed (in Miles Per Hour) given the wheel diameter, the number of revolutions and the total time of the trip. You can assume that the front wheel never leaves the ground, and there is no slipping or skidding.)

keil软件开发，基于89c52单片机的pwm控制直流电机，通过4*4按键设置pwm值，并且在1620上显示出pwm的值。(Keil software development, 89C52 MCU PWM control of DC motor based on PWM by setting 4*4 key values, and in the 1620 shows the value of pwm. )

用于全桥逆变电路的移相软启控制程序，周期和启动时间均可调节。(Phase-shifting soft-start control program for full-bridge inverters has adjustable cycle and start-up time.)

STM32F1、F4电机PWM调速及PID速度闭环控制(PWM Speed Regulation and PID Speed Closed-loop Control of STM32F1 and F4 Motors)