FM24CL04

说明：  通过不同的手势控制小车运动，实现小车的前进、后退、转弯等功能。(Through different gestures to control the movement of the car, the car can move forward, backward and turn.)

12864驱动程序（51串行）已通过检测，用时注意端口的定义(12864 Driver (51 serial))

说明：  风洞悬浮球程序 本程序来源于正点原子例程 芯片为STM32F103ZET6 超声波测距模块SR04 ILI9341主控的320*240液晶屏 程序使用超声波测距模块SR04测量透明亚克力管子内风洞悬浮乒乓球的位置， 输出给ILI9341主控的320*240液晶屏上，在屏幕上画出球的位置曲线。 可通过串口1输入修改PID参数以及悬浮球目标位置(Translate by GOOGLE from Chinese Wind tunnel suspension ball program This program is derived from the punctual atomic routine The chip is STM32F103ZET6 Ultrasonic ranging module SR04 320 * 240 LCD screen controlled by ILI9341 The program uses the ultrasonic ranging module SR04 to measure the position of suspended table tennis in a wind tunnel in a transparent acrylic tube. Output the position to the LCD screen with 320 * 240 resolution, and draw the position curve of the ball on the screen. Can modify PID parameters and hoverball target position through serial port 1 input)

可以用指令控制选择信道，设置发射功率，发送数据包（长度可选），接收数据包（接收时延可设），CC2430复位,内部温度传感器读取，定时器时长控制。底层函数基本做好，如果要加入新功能，可自行更改。(You can select the channel with the command control, set the transmit power, transmit data packet (lengths), receive data packets (receiver delay can be set), CC2430 reset, the internal temperature sensor reading, the timer duration control. Basic underlying function well, if you want to add new features to make changes.)

基于r7f0c809单片机的便携式电源，可以给手机等消费电子产品充电，具有过电流、过电压、过温保护功能。(The portable power supply based on r7f0c809 MCU can charge mobile phones and other consumer electronic products, and has the functions of over-current, over-voltage and over-temperature protection.)

只用于学习STM32F429的ADC，将一路ADC采集，改为两路ADC采集，并将采集的模拟量转换为紫外线等级。(It is only used to learn the ADC of STM32F429. It changes one ADC acquisition to two ADC acquisitions, and converts the analog acquisition to ultraviolet level.)

PLC基础及应用第2版廖常初主编 参考答案 （注未经允许禁止转载！）(PLC basic and applied 2nd Edition Liao Chang, editor suggested answers (note reproduced without permission prohibited!))

说明：  该文档详细描述了怎么去离线搭建ceedling环境(The document decribred how to build a ceedling test environment detailde)

说明：  本例程演示用汇编语言驱动DA,主要是针对51单片机的(This example shows using assembly language driver DA, mainly for 51 single)

单片机上电以后LCD屏上显示欢迎回家， 先验证指纹再验证密码 ，同时验证成功开锁 指纹和密码分别可以验证3次 3次都错蜂鸣器响 ，按下manage键进入管理员模式 可以修改密码 删减指纹，指纹用开关量表示(After the microcontroller is powered on, the LCD screen shows welcome home. First verify the fingerprint and then verify the password. At the same time, verify the successful unlocking fingerprint and password can verify that the buzzer rings three times and three times respectively. Press the management key to enter the administrator mode to modify the password and delete the fingerprint. The fingerprint is expressed by the switch.)