progMatlab

针对永磁同步电机常规直接转矩控制系统涉及到的问题,例如磁链的准确观测、定子电阻的变化、电压矢量开关表的改进以及滞环控制器的改进等等,本文都作了详细的分析,并提出了改进方案。为了提高系统的性能,本文将空间矢量调制的方法引入了常规直接转矩控制中,并在此基础上,对永磁同步电机无速度传感器问题作了详细的分析,总结了国内外的研究热点,提出了采用转子磁链矢量为基础的永磁同步电机直接转矩控制速度估计方法。仿真结果表明,该方案具有很好的动、静态特性。(Firstly, the paper analyzes the principle of direct torque control of permanent magnet synchronous motor and elaborates the impact of space voltage vector of the stator flux and the electromagnetic torque.Secondly, the paper introduces direct torque control of permanent magnet synchronous motor SVPWM technology.Under the same hardware conditions,the system can obtain More continuous voltage space vector by taking advantage of SVPWM.The simulation results show the program not only keeps the direct torque control fast dynamic response, but also reduce the motor torque ripple.)

基于块状导频的信道估计，包含MMSE等算法。(Based on the pilot block channel estimation, including the MMSE and other algorithms.)

OF,实际上OF是MCM Multi-CarrierModulation，多载波调制的一种。其主要思想是：将信道分成若干正交子信道，将高速数据信号转换成并行的低速子数据流，调制到在每个子信道上进行传输。正交信号可以通过在接收端采用相关技术来分开，这样可以减少子信道之间的相互干扰 ICI 。每个子信道上的信号带宽小于信道的相关带宽，因此每个子信道上的可以看成平坦性衰落，从而可以消除符号间干扰。而且由于每个子信道的带宽仅仅是原信道带宽的一小部分，信道均衡变得相对容易。在向B3G/4G演进的过程中，OFDM是关键的技术之一，可以结合分集，时空编码，干扰和信道间干扰抑制以及智能天线技术，最大限度的提高了系统性能。(OF)

基于matlab编程，给定几对初值，利用ode求解奔月的轨道示意图(Matlab-based programming, given a few of the initial value, the use of ODE solving flying to the moon orbit diagram)

This code is shah s iterative algorithm for selecting primary degrees of freedom in system reduction methodology.

可用于直流为电网，飞轮储能系统的研究。里面的模型可用(It can be used to study the flywheel energy storage system.)

解决图论中指定点到任意一点的最短路问题，并给出最短路径。(dijkstra)

本代码是matlab编写的程序集合，是学习matlab图像处理的利器。包括图像边缘检测、图像阈值分割等等。(This code is a set of programs written in matlab, learning matlab image processing tool. Including edge detection, image threshold segmentation and so on.)

预测控制算法程序，可以直接调用，很方便！(GPC program！)

相控阵天线阵列的密度加权matlab程序代码。 运行gui.m文件 lmax.m和lmin.mLinear_func.m最后几行被调用，放在和Linear_func.m路径相同的文件夹下即可 运行后command window里第一条分割线上面是第一幅图的几个值，第二条分割线上面是第二幅图的几个值。其中，peak_first是数值最大的峰值，peak_second是数值第二大的峰值(第一旁瓣)，theta_var是与 peak_first最近的左右两个谷值横坐标的距离。 因为是找半峰值点的，因为都是小数，在数组里没有正好等于主瓣幅值一半的点，只有接近一半的点，所以要设定一个范围比如大0.05或小0.05都认为是半峰值，但是有的数组里0.05的范围还是太小，所以可能报错。(Phased array antenna array the density weighted matlab program code. The last few lines of the run gui.m the file lmax.m lmin.mLinear_func.m call, same placed Linear_func.m path folder above the dividing line of the command window to run the first picture the several values ​ ​ above the dividing line several values ​ ​ of the second image. Wherein, peak_first numerical maximum peak the peak_second is the the numerical second largest peak (first sidelobe), the theta_var is the abscissa and peak_first recent about two valley distance. To find half the peak point are decimal, the array does not just equal to main lobe amplitude half points, only nearly half points, so you want to set a range, such as 0.05 or 0.05 are considered semi-peak some array, but the range of 0.05 or too small, it may be an error.)