programexample.rar

TMS320LF2407 DSP控制器的串行通信设计(TMS320LF2407 DSP serial communication controller design)

SIMULINK操作GPIO,实现定时让LED闪烁。(simulink operate GPIO)

28335直流电机控制程序，可以用的,控制过电机转动速度(28335 DC motor control procedures can be used)

1．EMIF 接口 TMS320F28335DSP 的扩展存储器接口(EMIF)用来与大多数外围设备进行连接，典型应用 如 连接片外扩展存储器等。这一接口提供地址连线、数据连线和一组控制线。ICETEK–F28335-A 将这些扩展线引到了板上的扩展插座上供扩展使用。 2．液晶显示模块的访问、控制是由28335ADSP 对扩展接口的操作完成。 控制口的寻址：命令控制接口的地址为 0x208001，数据控制接口的地址为0x208003 和 0x208004，辅助控制接口的地址为0x208002。 3．显示控制方法： -液晶显示模块中有两片显示缓冲存储器，分别对应屏幕显示的象素，向其中写入数值将改 变显示，写入“1”则显示一点，写入“0”则不显示。(The 1.EMIF interface Extended TMS320F28335DSP memory interface (EMIF) is used to connect with the most peripheral equipment, typical application Such as The connecting piece of extended memory. This interface provides the address lines, data lines and a set of control line. ICETEK- F28335-A The extension line to the extension socket for plate on the expansion of the use of. 2 liquid crystal display module access, control by the 28335ADSP to the extended interface operation is complete. Addressing control port: Command and control interface address 0x208001, the address data control interface for 0x208003 and 0x208004, auxiliary control interface address for 0x208002. 3 display control method: - liquid crystal display module with two display buffer memory, respectively corresponding screen pixel, writing values will be changed to the Change display, write "1" shows a little, write "0" are not displayed.)

dsp上实现的音频经典混响算法,四个梳状滤波加两个全通滤波器实现(dsp audio to achieve the classic reverb algorithms, 4 comb filter plus two all-pass filter to achieve)

web控制端，下载后看readme进行安装使用(english one two three four five six seven eight nine ten)

说明：  28335例程，自己仔细的研究了一阵子，觉得不错，可参考。(28335 routines, good for reference)

本程序时DSP上实现的图像中值滤波，首先将dat文件导入TI开发的CCS上进行处理，其中在CCS上的编程用的是C语言编写。其中dat文件先通过matlab将图片转化得到的。(This program is implemented on a DSP image median filtering, first developed by TI dat file into CCS on the treatment, which in the CCS is used on the C programming language. Dat files of which the first through matlab to get into the picture.)

基于matlab的波束成形算法，能够选择性过滤某一方向的波，可以配合vivado进行硬件联合仿真。(Beamforming algorithm based on Matlab can selectively filter the wave in a certain direction, and can cooperate with vivado for hardware co-simulation.)

创龙DSPC6748开发板例程, 大家可以学习研究下(example for chuanglong C674)