zcyfft

在matlab环境下实现对信号的小波变换；小波变换工具箱(wavelet toolbar)

用MATLAB编写的一个8级m序列，并实现了调频序列的提取和频率的选择，能显示出跳频图案！(Prepared with an 8-level MATLAB m sequence, and realized the extraction sequence and frequency of FM option, can show frequency-hopping pattern!)

M62429芯片控制源子程序，直接可以掉用的比较好的一个子程序(M62429 chip of control subroutine, direct swap can be used in relatively good one subroutine)

maplestory version 102 sourcecode

国外计算机科学教材系列，模式识别第四版课后习题部分matlab源码，李晶皎，王爱侠等译(Foreign computer science textbook series, the fourth edition of after-school exercise part of pattern recognition matlab source, Jiao Jing, Wang Aixia translated)

在程序中用一般的MUSIC方法估计了信号的频谱，从两图中可看出在信号各频率处，频谱的峰值较大，故能明显的与噪声相区别，可在一定程度上避免在信号幅度较小时信号被噪声淹没的情况。(MUSIC method general procedures used to estimate the spectrum of the signal, it can be seen from the two graphs in the signal at each frequency of the spectrum peak larger, and it could be significantly distinguished from noise in the signal can be avoided to some extent a lesser extent, the signal is noise submerged.)

三相无源逆变的仿真，采用双闭环控制，PT调节器。(Passive three-phase inverter simulation, using the double closed loop control, PI regulator )

一端关于数字化信道接收机的源码，作毕设时用的，希望对大家有用(end of the digital channel receiver source for complete use of the established, we want to help! !)

MATLAB行情软件MatlabTraderGUI 1.完成了日线、周线、月线等不同周期的展示。 2.完成了MACD,BOLL,RSI,W&R,OBV,DMI,PVT等技术指标的展示。左上的两个均线的长度参数可以动态修改展示。 3.增加了展示范围的调整。(相当于普通行情软件的上下键) 4.增加了水平的slider用来滚动展示K线。（相当于普通行情软件的左右键） 5.拖动水平的slider，三个axes可以同步移动（拖动）。 6.按下鼠标左键，可以展示十字光标，右面的table可以展示十字光标处的 开高低收量。 7.在每个axes都增加了右键，可以进行图片另存为。 8.老规矩，Mcode我打包一并放出来，想用的拿去，可以直接改源代码，作为学习GUI是个不错的范例，我为人人，人人为(MATLAB software market MatlabTraderGUI 1 completed the daily, weekly different cycles, such as monthly show. 2 complete shows MACD, BOLL, RSI, W & R, OBV, DMI, PVT and other technical indicators. The average length of the upper-left of the two parameters can be modified dynamically show. 3 shows an increase adjustment range. (Equivalent to ordinary market down key software) 4. The slider to increase the level of K-line scrolling display. (Equivalent to about key common market software) 5 Drag the horizontal slider, three axes can be synchronized to move (drag). 6 Press the left mouse button, you can display the crosshairs, the right of the table can show opened at the level of the yield of the crosshairs. 7 have increased in each of the axes right, the picture can be saved as. 8 old rules, Mcode I packed together put out, want to take it to use, you can directly change the source code as a learning GUI is a good example, one for all, all for one )

highpass enhancementfor MRI breast