-
references
references for matlab search
- 2010-12-08 08:11:17下载
- 积分:1
-
imgsuanfa
用matlab编写的图像复原程序,好用,大家可以试一下-Prepared to use matlab image restoration procedures, easy to use, everyone can try(Prepared to use matlab image restoration procedures, easy to use, everyone can try)
- 2009-06-06 14:28:22下载
- 积分:1
-
jingxiangchazhi
这是一种导频辅助的径向线性插值信道估计算法,算法来自于12年3月份的IEEE,画出比特信噪比与误码率的关系曲线.(This is a polar-linear lnterpolation aided channel estimation algorithm,which comes from IEEE in march 2012,drawn-bit signal to noise ratio and bit error rate curve.)
- 2012-06-17 22:35:14下载
- 积分:1
-
framefreeoscillation
采用有限单元法计算平面刚架自振频率,可生成单刚、单元质量阵并组成总刚、总质量矩阵,并绘图显示。(Plane frame using the finite element method to calculate the natural frequency can be generated just a single unit consisting of the total mass matrix and just total mass matrix, and graphics.)
- 2013-12-30 15:29:08下载
- 积分:1
-
Data-and-Networking-Solutions-P3
Data Communications and Networking Solutions(ch11-20)(Data Communications and Networking Solutions (ch11-20))
- 2013-11-30 23:21:43下载
- 积分:1
-
GA
说明: 遗传算法源代码,可以用于matlab程序,欢迎大家使用。(Genetic algorithm source code, can be used matlab program, welcome everyone to use)
- 2015-03-13 15:39:25下载
- 积分:1
-
surface_wave_detection
地波超视距雷达系统仿真 雷达信号处理 超视距雷达(Ground wave over-the-horizon radar system simulation Radar Signal Processing)
- 2020-06-29 01:20:01下载
- 积分:1
-
grd_test
xwch_test.m是主测试文件;biaoji.mat存放滤波器系数;xiangweicha.m用FFT计算相位差。
仿真框架为:
1.标记信号和双音信号续接作为发送信号;
2.对双音中一个频率分量的相位做偏移,再经过一个低通滤波器(引入线性相位,模拟收发不能同步测量现象)后,作为收到的信号;
3.用一个检测信号对收发信号进行相关运算;
4.画出收发信号以及相关处理后的信号。找出相关信号的那个尖点,从而推算出收发双音信号0相位点;
5. 输入0相位点位置,计算相对相位差。(xwch_test.m is the main test file biaoji.mat store filter coefficients xiangweicha.m calculated using FFT phase difference. Simulation framework: 1. Mark signals and then as a two-tone signal continued to send signals 2. On a two-tone frequency components of the phase shift to do, and then through a low pass filter (the introduction of linear phase, simulation can not simultaneously send and receive measuring the phenomenon), the as received signal 3. using a detection signal of the transceiver signal correlation operation 4. draw send and receive signals and related processed signal. Correlated signal of the cusp, which calculate the two-tone signal transceiver 0 phase point 5. Enter 0 phase point position, calculate the relative phase difference.)
- 2010-06-12 17:31:00下载
- 积分:1
-
Example-of-Supercritical-Hopf-bifurcation
there is a matlab cod,that is, Example of Supercritical Hopf bifurcation.
- 2013-08-22 16:32:22下载
- 积分:1
-
Rectifier-design
rectifier design in matlab
- 2013-09-15 09:41:39下载
- 积分:1