登录
首页 » C++ Builder » Code

Code

于 2011-02-22 发布 文件大小:29KB
0 167
下载积分: 1 下载次数: 0

代码说明:

说明:  设计一个正弦信号发生器,使用凌阳公司的16位单片机SPCE061A作为中央控制器,结合DDS芯片AD9850,产生0~15MHz频率可调的正弦信号,正弦信号频率设定值可断电保存;使用宽频放大技术,在50Ω负载电阻上使1K~10MHz范围内的正弦信号输出电压幅度VP-P=6V±1V;产生载波频率可设定的FM和AM信号;调制信号为1KHz的正弦波,调制信号的产生采用DDS技术,由CPLD和Flash ROM加上DAC进行直接数字合成;二进制基带序列码由CPLD产生,在100KHz固定载波频率下进行数字键控,产生ASK,PSK信号。(Design of a sinusoidal signal generator, the use of Sunplus 16-bit MCU SPCE061A as the central controller, combined with DDS chip AD9850, have adjustable frequencies 0 ~ 15MHz sinusoidal signal, sinusoidal signal frequency settings can be stored power using broadband amplification, in a 50Ω load resistor to 1K ~ 10MHz sinusoidal signal within the output voltage amplitude VP-P = 6V ± 1V generating the carrier frequency of the FM and AM can be set signal 1KHz sine wave modulation signal, modulated signal generation using DDS technology, coupled by the CPLD and Flash ROM DAC for direct digital synthesis binary baseband sequence code generated by the CPLD in a fixed carrier frequency 100KHz digital keying, resulting in ASK, PSK signals.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • pic
    PIC18系列单片机范例,包括各部分的调试(PIC18 MCU examples, including the part of the debugging)
    2009-04-28 17:18:06下载
    积分:1
  • TCTL
    实时水流加热,可控水温的温度,经过水流量来精确控温无过冲热,温控精度高(heat flow watter!)
    2013-07-29 11:47:47下载
    积分:1
  • STM32超声波
    基于stm32f103的超声波测距程序,利用keil编写(Ultrasonic ranging based on STM32F103)
    2020-07-04 04:20:01下载
    积分:1
  • C8051F全系列例程代码
    C8051F全系列例程代码,适合初学者,可通过跑例程快速上手。(C8051F full series of routine code, suitable for beginners, can run a routine quickly on.)
    2018-12-03 15:25:36下载
    积分:1
  • MATLAB-and-51-
    单片机和matlab串口通信程序,简单易用(Microcontroller and matlab serial communication program, easy to use)
    2015-03-24 10:18:39下载
    积分:1
  • PLCpcb
    国外PLC设计的原理图和PCB(Principle foreign PLC design and PCB)
    2016-06-02 14:20:50下载
    积分:1
  • 1
    说明:  51单片机控制 套丝机机床实现自动加工螺纹钢(motor cw ccw)
    2013-11-15 00:07:21下载
    积分:1
  • G2553serial
    MSP430G2553串口工程代码 已经调试成功(MSP430G2553 serial debugging code has been successfully engineering)
    2015-01-21 18:31:27下载
    积分:1
  • zhiliudianliuyuan
    本系统以直流电流源为核心,AT89S52单片机为主控制器,通过键盘来设置直流电源的输出电流,设置步进等级可达1mA,并可由数码管显示实际输出电流值和电流设定值。本系统由单片机程控输出数字信号,经过D/A转换器(AD7543)输出模拟量,再经过运算放大器隔离放大,控制输出功率管的基极,随着功率管基极电压的变化而输出不同的电流。单片机系统还兼顾对恒流源进行实时监控,输出电流经过电流/电压转变后,通过A/D转换芯片,实时把模拟量转化为数据量,再经单片机分析处理, 通过数据形式的反馈环节,使电流更加稳定,这样构成稳定的压控电流源。实际测试结果表明,本系统输出电流稳定,不随负载和环境温度变化,并具有很高的精度,输出电流误差范围±5mA,输出电流可在20mA~2000mA范围内任意设定,因而可实际应用于需要高稳定度小功率恒流源的领域。(the system to DC current source to the core, MCU AT89S52 main controller, through the keyboard to set up DC power supply output current, set up to 1mA Stepping grades, digital control can be shown by the actual output current value and current setting. The system consists of programmable microcontroller digital signal output, after the D/A converters (AD7543) analog output. After Operational Amplifiers isolation, amplification and control of the output power base. With the power of the base voltage changes in the output current. SCM system also takes on the constant current source for real-time monitoring, after current output current/voltage changes, the A/D converter chip, real-time conversion from analog to the volume of data and then analyzed by the MCU, through data link in the )
    2006-06-27 08:41:38下载
    积分:1
  • LCDMEUN
    说明:  LCD多级菜单具体实现源代码,附原理图。(LCD multi-level concrete realization of the source code for the menu)
    2009-08-24 14:23:48下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载