登录
首页 » matlab » wenlituxiangfengelunwenheyuanma

wenlituxiangfengelunwenheyuanma

于 2010-03-13 发布 文件大小:2004KB
0 312
下载积分: 1 下载次数: 179

代码说明:

  纹理图像分割论文和代码,还算比较完整的,对做方面毕业设计的有点用!(Texture image segmentation papers and code are fairly more complete, to make the design a bit to use in graduate!)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • ExperimentswithMATLAB
    Matlab for Experiments
    2009-07-15 23:08:31下载
    积分:1
  • juanjima
    采用matlab编程,实现卷积码的编码与译码(Using matlab programming, coding and decoding convolutional codes)
    2011-05-10 13:22:33下载
    积分:1
  • OTSU
    大津法确定图像二值化阈值,为MATLAB语言编写的M文件, 可直接使用(Otsu method to determine the threshold image binarization)
    2013-03-09 16:29:30下载
    积分:1
  • antenna_simulation_matlab
    《通信天线建模与MATLAB仿真分析》一书配套matlab程序( Communications antenna modeling and MATLAB simulation analysis, a book matching matlab program)
    2008-02-25 21:24:40下载
    积分:1
  • activeContoursSnakesDemo
    本演示实现了主动轮廓模型由Kass等人提出。 要运行它的图形用户界面 1。基于MATLAB型引导提示。 2。关于“到现有的图形用户界面,点击” 3。选择在与本文件相同的目录snk.fig文件 4。按一下上方的绿色箭头启动图形界面 一旦GUI已经启动,您可以通过使用蛇 1。点击“新形象”,并加载输入图像。提供的样品图像。 2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。 3。只要你点击“过滤器”,头发会出现交叉,用他们和你左击鼠标,您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下,你应该单击对象周围的一切你想要的部分。最后一点,必须挑选使用右键单击,以阻止更多的积分为MATLAB的要求。 4。设置各种蛇参数(在能源方面的相对权重的蛇目标函数)或离开它们的默认值,然后按一下他们“迭代”按钮。蛇会出现和移动,因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al. To run it with GUI 1. Type guide on the matlab prompt. 2. Click on "Go to Existing GUI" 3. Select the snk.fig file in the same directory as this file 4. Click the green arrow at the top to launch the GUI Once the GUI has been launched, you can use snakes by 1. Click on "New Image" and load an input image. Samples image are provided. 2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image. 3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points. 4. Set the various snake paramete)
    2010-07-05 11:54:13下载
    积分:1
  • Math
    Matlab算法分析与设计程序,包括很多搜索算法的源程序。(Matlab algorithm analysis and design procedures, including many search algorithm of the source.)
    2010-10-15 14:10:33下载
    积分:1
  • pmmotor
    永磁同步电机矢量控制.mdl文件 0.04s突减负载,双闭环电流、转速反馈(pmsm concle system at 0.04s down the T, then look at the scope)
    2012-04-30 12:20:08下载
    积分:1
  • hist
    这个代码是有关histogram处理的代码,要在matlab软件上运行(histogram processing code)
    2014-10-13 08:54:18下载
    积分:1
  • MATLAB命令行下mcc命令示范3-MccTest3
    MATLAB命令行下mcc命令示范3(MATLAB command line mcc orders Model 3)
    2005-04-03 14:19:14下载
    积分:1
  • matlab_PLLpost
    这个程序是用来对pllpost进行仿真的,该思想基于多方面的考虑(This procedure is used to pllpost simulation, based on the thinking of a number of considerations)
    2006-11-01 19:11:23下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载