ccorr

出租车的计费功能的实现,计量模块、计费模块、控制模块、译码模块。(taxi fee)

M6e 超高频读写器相关调试源代码和相应文档(M6e UHF reader related debugging source code and corresponding documentation)

德国低干扰谱，以及公路C级路面的路面不平度的c++实现。一些相关的资料，便于初学者理解。(German low interference spectrum, as well as C-level road highway pavement roughness achieved. Some relevant information, easy for beginners to understand.)

根据burg算法实现的AR模型功率谱计算(Burg algorithm AR Model Power spectrum calculation)

说明：  利用共轭梯度法求线性方程组的Matlab算例(Using conjugate gradient method for solving linear equations Matlab examples)

张德丰matlab小波分析源代码，从信号时-频联合分析引入小波变换，将信号的多分辨率分析及Mallat算法作为全书的重点，并在此基础上，进一步阐述了双正交小波多分辨率分析、小波包多分辨率分析、提升小波应用，还讲述了小波分析在奇异性检测、去噪及数据压缩中的应用。(Zhang Defeng Matlab wavelet analysis of the source code from the signal- frequency joint analysis of the introduction of wavelet transform, multi-resolution analysis of the signal and Mallat algorithm as the focus of the book, and on this basis, further elaborated biorthogonal wavelet multi-resolution analysis wavelet packet multi-resolution analysis, the lifting wavelet applications, but also about the application of wavelet analysis in the singularity detection, de-noising and data compression.)

通过检验相关系数进行多变量灰色预测 用MATLAB 编制(By examining the correlation coefficients are more variable gray forecast prepared with MATLAB)

Introduction to Stochastic Search and Optimization

一般情况下，我们都是在MATLAB命令行或DOS命令行下编译MEX程序。 所用的命令就是：mex filename.c 这有很多不方便的地方： a. 虽然mex也可以编译C++的mex程序，但是它的主框架仍是C的 a. 当程序有多个模块时，需要多次使用mex命令，操作很麻烦 b. 不能利用VC特有的ClassWizard自动创建和维护类 c. 不能用MFC类库编写应用程序 d. 不能方便地进行类似VC的项目管理 本文详细解说如何在IDE中编译MEX程序(Under normal circumstances, we are all in the MATLAB command line or DOS command line program to compile MEX. Command is used by: mex filename.c This has a lot of inconvenient places: a. Although the mex can also compile C++ The mex program, but it is still the main frame C of a. When the procedure has a number of modules the need to repeatedly use the mex command, the operation is cumbersome b. Can not use VC-specific ClassWizard automatically create and maintain the category c. can not use MFC class library to write applications easily d. should not conduct a similar project management VC a detailed explanation of how this article IDE compiling MEX procedures)

“基于Floyd最短路算法的Ford和Fulkerson迭加算法”的最小费用最大流算法，其基本思路为：把各条弧上单位流量的费用看成某种长度，用Floyd求最短路的方法确定一条自V1至Vn的最短路；再将这条最短路作为可扩充路，用求解最大流问题的方法将其上的流量增至最大可能值；而这条最短路上的流量增加后，其上各条弧的单位流量的费用要重新确定，如此多次迭代，最终得到最小费用最大流。 (" Floyd shortest path algorithm based on the Ford and Fulkerson algorithm superposition" of the minimum cost maximum flow algorithm, the basic idea is: the flow of each arc on the unit cost as a length, with Floyd for the most short-circuit method to determine a from V1 to Vn of the most short-circuit then this can be expanded as the shortest way, by solving the maximum flow of traffic on the way to its maximum possible value and this increased the flow of the shortest path, on which the arcs of the unit to re-determine the cost of traffic, so several iterations, finally get the minimum cost maximum flow.)