登录
首页 » matlab » AAM

AAM

于 2010-12-25 发布 文件大小:3394KB
0 321
下载积分: 1 下载次数: 667

代码说明:

  主动外表模型与主动形状模型,MATLAB平台下使用,内含DEMO(active appearance model)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • macfir
    设计一个 MAC FIR滤波器 设计一个 MAC FIR滤波器(The design of a MAC FIR filter design of a MAC FIR Filter)
    2008-01-01 11:14:20下载
    积分:1
  • RLS代码
    RLS算法语音降噪,使得语音信号更加清晰。(Speech noise reduction in RLS algorithm,To make the voice signal more clear.)
    2018-04-19 14:59:48下载
    积分:1
  • PredictPower
    为提高了短期负荷预测的精度根据季节气候的不同做不同的模糊处理并建立专家处理系统对天气做的模糊处理使预测结果令人满意(to a rise in short-term load forecasting accuracy under different seasonal climate so different fuzzy treatment and the establishment of the Expert Jimmy system for weather so fuzzy treatment made forecasting satisfactory results)
    2007-04-04 13:31:12下载
    积分:1
  • compensation-program
    matlab的光照补偿程序,可以运行,挺有用的(Matlab Illumination compensation program, you can run quite used)
    2013-07-10 14:02:10下载
    积分:1
  • matlab-commenly-used-order
    matlab的常用函数速查,包括了大部分常用函数,用ctrl+f就可以直接查找。(including matlab commonly used functions, including the most commonly used functions, you can search the functions using ctrl+f .)
    2013-12-27 14:04:50下载
    积分:1
  • mymatlab
    LDPC 码matlab程序 ,可用matlab直接运行,输出为BER曲线(LDPC code matlab program, matlab can be used directly to run, the output for the BER curves)
    2008-04-06 15:51:25下载
    积分:1
  • param_DH
    this program stimated the parameterDH of a robot
    2010-11-16 12:46:03下载
    积分:1
  • Spectrum-Analysis
    说明:  在地震勘探资料处理中应用的频谱分析函数。。。。。。。。。。。。。。。。。。。。。(Spectrum Analysis)
    2011-03-31 12:31:32下载
    积分:1
  • power_wind_ig
    用simulink对风电场进行建模分析得到功率以及电流的仿真图(This example uses an initial state vector to start the simulation steady-state. When you make changes to the model (add, delete, rename blocks, etc), the initial state vector needs to be regenerated or disabled, otherwise Simulink signals an error when the simulation is started. To disable the use of initial state vector for this model, go to the Data Import/Export section of the Model Configuration Parameters tool and uncheck the Initial state option under the Load workspace section. To regenerate the initial state vector after a change to the model, follow the instructions given in the initialization file for this model. Type open( init_power_wind_dfig ) at the matlab prompt to view this file.)
    2015-07-24 13:48:45下载
    积分:1
  • pend
    Engineering dynamics example using simulink and calculating the natural frequency of the system
    2010-09-17 17:13:12下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载