-
电力系统潮流计算
实现线性的电力系统潮流计算,分别为首端电压末端功率和末端电压末端功率,可实现一定精度的迭代计算(Power flow calculation in power system)
- 2019-01-25 17:22:46下载
- 积分:1
-
JPDA
用JPDA进行数据互联的多目标跟踪程序,仿真中用了2个目标,MATLAB编写。(JPDA connected with the multi-objective data tracking program, the simulation using the two goals, MATLAB write.)
- 2011-05-25 14:29:30下载
- 积分:1
-
spear
斯皮尔曼秩相关系数,可用于两对序列的相关统计分析,越大表示相关性越强。(Spearman s rank correalation coefficient)
- 2009-09-25 14:15:47下载
- 积分:1
-
DATA16M
这是在MATLAB环境下进行电力系统暂态稳定分析的pst源程序,该文件定义了一个16机的系统模型。(This is the MATLAB environment in power system transient stability analysis of the pst source, the document defines a 16-machine system model.)
- 2008-07-18 11:41:55下载
- 积分:1
-
moon_pos_vel_J2000
通过坐标转换的方法估算月球在某一时刻在J2000坐标系下的位置和速度。(理解航天中坐标转化、时间系统的学习案例)(Through the coordinates of the conversion method to estimate the moon at a time in the J2000 coordinate system under the location and speed. (Understanding of aerospace coordinate transformation, time system learning case))
- 2020-10-07 20:17:36下载
- 积分:1
-
PV-Controller
光伏控制器,自动充放电控制12V/10A光伏控制器(ERA-04-10-A):
额定工作电压:DC12V
最大充电电流:10A
最大放电电流:5A/路(共两路负载)
太阳能组件开路电压:25V
空载电流:<15mA
温度补偿:-20Mv/°C
工作环境温度:-25°C~+50°C
使用海拔:<5500M
控制器尺寸(mm):
光控电压(25°C):<=3.3V
过放保护电压(25°C):<10.8V
过放恢复电压(25°C):>10.8V
过充保护电压(25°C):>15.0V
过压保护电压:17.68V
过压恢复电压:14.7V
浮充电压(25°C):13.4V~13.7V
恢复正常充电电压(25°C):13.2V
结束正常充电电压(25°C):15.0V
(PV controller, automatic charge and discharge control 12V/10A PV controller (ERA-04-10-A): Rated voltage: DC12V Maximum charge current: 10A Maximum discharge current: 5A/Road (a total of two loads) Solar components of the open circuit voltage: 25V No-load current: < 15mA Temperature Compensation:-20Mv/° C Operating Temperature:-25 ° C ~+50 ° C with elevation: < 5500M Controller Size (mm): light control voltage (25 ° C): < = 3.3V over-discharge protection voltage (25 ° C): < 10.8V over-discharge recovery voltage (25 ° C):> 10.8V overcharge protection voltage (25 ° C):> 15.0V over-voltage protection Voltage: 17.68V overvoltage recovery voltage: 14.7V float voltage (25 ° C): 13.4V ~ 13.7V back to normal charging voltage (25 ° C): 13.2V end of the normal charging voltage (25 ° C): 15.0V)
- 2021-04-22 17:08:48下载
- 积分:1
-
example
管道应力分布,利用ansys mechanical APDL命令流进行计算(Pipeline stress distribution is calculated by using ANSYS mechanical APDL command stream.)
- 2018-06-13 11:36:07下载
- 积分:1
-
jdwx
家电维修源码自用的
家电维修源码自用的(jiadianweixiuyuanma ziyongde)
- 2012-04-06 17:39:14下载
- 积分:1
-
RotorCampbell
ansys计算转子轴系临界转速,画坎贝尔图的源代码(ansys rotor shaft critical speed calculation, painting Campbell diagram of the source code)
- 2013-11-15 14:41:01下载
- 积分:1
-
IndirectAdjustment
测量平差程序设计:边角网间接平差,provide the translate rad to angle(Indirect Adjustment)
- 2020-11-18 15:19:38下载
- 积分:1