-
CT
说明: 图像反投影重建算法,利用CT采集的数据在进行R_L_滤波后进行反投影得到检测图像。(Image reconstruction algorithm, using the projection of the data collected on CT after R_L_ filter back-projection get detection images.)
- 2010-01-05 12:10:13下载
- 积分:1
-
convolutive
卷积盲源分离,采用matlab编程,带有说明文档。(convolution Blind Source Separation using Matlab programming, with documentation.)
- 2020-06-30 12:00:02下载
- 积分:1
-
Fz
说明: K分布仿真的一部分,一部分是斑纹分量 还有是结构分量 两者点乘得到K分布序列 (K distribution part of the simulation, in part, there is a structural component markings component of both the dot distribution sequence obtained K)
- 2013-12-03 18:28:37下载
- 积分:1
-
scilab
说明: Scilab软件与MATLAB功能相似,而且它是一个开源项目。功能强大,使用方法不简单。本教材是学习此软件较详细的资料。(Scilab software with features similar to MATLAB, and it is an open source project. Powerful, simple to use. The materials to learn the software more detailed information.)
- 2008-10-20 22:36:29下载
- 积分:1
-
cyclicpursuit
循环追踪算法程序,用于平面内多个体系统的分布式控制,能够达到收敛的目的,控制所需信息量少。(This code is about the cyclic pursuit algorithm which is used for controlling of formation moving in a plane.)
- 2012-03-29 00:41:09下载
- 积分:1
-
wavelet-coherence-master12
关于脑电信号处理,的一个类似于eeglab的应用包,可在matlab上直接使用(About EEG signal processing, a similar eeglab application package, can be used directly on the MATLAB)
- 2020-07-23 09:48:43下载
- 积分:1
-
digitalprocess
数字信号处理报告MATLAB产生和图形显示实验报告。(Digital Signal Processing MATLAB report generation and graphical display experimental report.)
- 2008-01-12 22:19:59下载
- 积分:1
-
multi_array
仿真了相控阵雷达的天线方向图,能进行不同的状态参数设置,产生的天线方向图(Simulation of a phased array radar antenna pattern, can be a different state parameter settings, resulting antenna pattern)
- 2020-07-01 19:40:01下载
- 积分:1
-
work111.rar
说明: 名称:work111
大小: 9KB
完成时间:Wed Aug 17 16:30:23 2005
基于SIMULINK的模糊控制系统仿真程序
(name : work111 Size : File completion : Mon Aug 17 16:30:23 2005 Simulation of Fuzzy Control System Simulation Program)
- 2005-09-14 14:40:46下载
- 积分:1
-
three_dim_plot
The model used for creating the reference voltage is shown
in Fig. 4. First, photovoltaic output current (Ipv) and output
voltage (Vpv) are passed through a first order low pass filter
with a magnitude of G = 1 and a time constant of T = 0.01
seconds in order to filter out the high frequency components
or harmonics from these signals as shown in Fig. 5 and Fig. 6.
The filtered current and voltage signals (Ipv_F and Vpv_F) are
then fed into the MPPT control block that uses the Incremental
Conductance Tracking Algorithm. An algorithm that is based
on the fact the slope of the PV array power curve shown in
Fig. 7 is zero at the Maximum Power Point (MPP), positive on
the left of the MPP, and negative on the right. The MPP can
thus be tracked by comparing the instantaneous conductance
(I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):
- 2013-07-23 17:56:06下载
- 积分:1