-
image_change_detecting
图像变化检测算法,由t检验得到差分图像的变化掩膜。左后成功检测到图像中运动的物体。(Image change detection algorithms have been tested by the t change difference image mask. Left a successful campaign to detect objects in images.)
- 2009-04-25 10:04:10下载
- 积分:1
-
Wave
说明: 《MATLAB小波分析》书本实例源程序。
希望为各位的学习带来方便!(MATLAB wavelet analysis examples of source books.I want to bring convenience to learning!)
- 2009-08-13 10:57:31下载
- 积分:1
-
proses_acak_WSS
proses acak WSS, percobaan sistem komunikasi dengan menggunakan matlab
- 2013-11-26 07:43:14下载
- 积分:1
-
28726
截取一段音频信号作为输入信号,分别通过低通,高通和带通滤波器,比较滤波效果。(Interception of an audio signal as an input signal, respectively, through a low pass, high pass and band-pass filter, compare filtering effect.)
- 2020-11-13 10:29:43下载
- 积分:1
-
MATRIX
Matlab的精华在于其丰富的矩阵运算,本文结合《矩阵论》的相关知识,较为详尽地介绍了大量矩阵运算的matlab实现。(Matlab essence lies in its rich matrix operations, this paper " Matrix theory," the relevant knowledge, a more detailed introduction to the large number of matrix operations matlab.)
- 2013-06-01 18:44:21下载
- 积分:1
-
matlab_code_glonass
forming of a signal, GLONASS system, coherent reception, graph autocorrelation, crosscorrelation function, bit-error probability[SNR]
- 2009-03-01 03:36:22下载
- 积分:1
-
OQPSK
说明: OQPSK的Matlab/Simulink调制解调仿真系统,包括匹配滤波,载波恢复,定时恢复等重要模块,可以观察眼图,仿真误码率,帮助理解OQPSK系统(OQPSK Matlab/Simulink simulation system modulation and demodulation, including matching filter, Carrier Recovery, timing recovery and other important module, we can observe the eye, simulation BER help understand OQPSK system)
- 2005-11-26 14:06:37下载
- 积分:1
-
ncmgui
主要是针对面向对象设计中的模块应用,详细见英文说明。。。(NCMGUI Master GUI for Numerical Computing with MATLAB.
NCMGUI provides an interface to nineteen of the graphical demostrations
from "Numerical Computing with MATLAB". Click on any graphic to access
the underlying function.)
- 2013-10-30 14:56:57下载
- 积分:1
-
chuanliandiandan
永磁同步电机直接转矩控制,转矩闭环,磁链闭环(Permanent magnet synchronous motor direct torque control, closed-loop torque, flux closed-loop)
- 2013-05-11 21:39:48下载
- 积分:1
-
manual_label
一个MATLAB GUI程序,可以方便地用来手动标记正训练样本和负训练样本。
——————————————————
1.首先输入要标定的数据库目录、要存放正训练样本的目录、要存放负训练样本的目录
2.点击“开始”,程序自动依次显示数据库目录中的图片
3.点击“正例”或“反例”将会把当前图片复制到相应目录
4.可以在图片上点击拖动圈出一个区域,以截取圈出的区域作为样本
5.选中“约束选取比例”可以使得最终选取的样本有固定的大小(A matlab GUI program that can be used to label training samples manually.
It contains rich functions)
- 2012-01-02 10:44:37下载
- 积分:1