geneticalgrithmoptimizeRBF

此文件包含有四个基于matlab源程序,可直接运行.其说明如下 P0305：模拟图像受高斯白噪声和椒盐噪声的影响 P0306：采用二维中值滤波函数medfilt2对受椒盐噪声干扰的图像滤P0307：采用MATLAB中的函数filter2对受噪声干扰的图像进行均值P0308：图像的自适应魏纳滤波 (This file contains four based on the matlab source code can be directly run. Its description is as follows P0305: analog image by Gaussian white noise and salt and pepper noise P0306: A two-dimensional median filtering function medfilt2 by salt and pepper noise to the image filter P0307: the use of MATLAB in filter2 function affected by noise interference images mean P0308: Image Adaptive Weiner Filter)

直线加速器twiss参数匹配，matlab模拟(linac twiss parameter matching, Matlab simulation)

big great world if at on in upon secondary selection under table. For the time now till down

说明：  异步电机矢量控制，异步电动机具有非线性、强耦合、多变量的性质，要获得高动态调速性能，必须从动态模型出发，分析异步电动机的转矩和磁链控制规律，研究高性能异步电动机的调速方案。矢量控制系统和直接转矩控制系统是已经获得成熟应用的两种基于动态模型的高性能交流电动机调速系统。矢量控制系统通过矢量变换和按转子磁链定向，得到等效的直流电动机模型，然后模仿直流电动机的控制策略设计控制系统。(Vector control of asynchronous motor, asynchronous motor has the characteristics of non-linear, strong coupling and multi variable. In order to obtain high dynamic speed regulation performance, we must start from the dynamic model, analyze the torque and flux control law of asynchronous motor, and study the speed regulation scheme of high-performance asynchronous motor. Vector control system and direct torque control system are two kinds of High-Performance AC motor speed control system based on dynamic model, which have been widely used. The vector control system obtains the equivalent DC motor model through vector transformation and rotor flux orientation, and then designs the control system by imitating the control strategy of DC motor.)

This is a matlab that contain the circuit of the power factor. It is in 3 phase.

归一化二阶响应系统 gui设计 很不错的一个程序 (Normalized second-order response system is pretty good gui design a procedure)

PNN and K-mean algorithm

光伏电池建模与MPPT算法和DCDC电路建模，能实现MPP的锁定(Modeling of photovoltaic cells, MPPT algorithm and DCDC circuit can achieve MPP locking.)

MVDR算法的频率谱估计 包含1个目标信号和2个干扰信号(Frequency Spectrum Estimation of MVDR Algorithm Contains one target signal and two interference signals)

该程序用于计算n根平行导线间的串扰,程序结构及说明见程序内。源可以是单频的或脉冲的（这里给出的是频域的）。频率、波形、线长、电源及负载阻抗均可在用MATLAB编写的语句中方便地修改。但必须输入导线系统每单位长度的电感、电容矩阵。(The procedure used to calculate n root of crosstalk between parallel wires, program structure and description of process. Source can be single frequency or pulse (here is given by the frequency domain). Frequency, waveform, the line is long, power and load impedance can be found in the use of MATLAB statements prepared easily modified. However, the system must enter a wire per unit length inductance, capacitance matrix.)