fanyi

code for maximum likelyhood in matlab

NP是美国匹兹堡大学的T.L.Saaty 教授于1996年提出了一种适应非独立的递阶层次结构的决策方法，它是在网络分析法（AHP）基础上发展而形成的一种新的实用决策方法。其关键步骤有以下几个： 1 确定因素，并建立网络层和控制层模型。 2 创建比较矩阵。 3 按照指标类型针对每列进行规范化。 4 求出每个比较矩阵的最大特征值和对应的特征向量。 5 一致性检验。如果不满足，则调整相应的比较矩阵中的元素。 6 将各个特征向量单位化(归一化)，组成判断矩阵。 7 将控制层的判断矩阵和网络层的判断矩阵相乘，得到加权超矩阵。 8 将加权超矩阵单位化(归一化)，求其K次幂收敛时的矩阵。其中第j列就是网络层中各元素对于元素j的极限排序向量。 (NP is a professor at the University of Pittsburgh TLSaaty presented in 1996, an adaptation of non-independent Hierarchy of decision-making method, which is the analytic network process (AHP) formed on the basis of the development of a new and practical decision-making method . The key steps are the following: A determining factor, and a network layer and control layer model. 2 create a comparison matrix. For each of the three types of indicators in accordance with normalized columns. 4 find the maximum for each comparison matrix eigenvalue and the corresponding eigenvectors. 5 consistency test. If not satisfied, then the comparison to adjust the corresponding matrix elements. 6 will each feature vector units of (normalized), to determine the composition of matrix. 7 to determine the control layer and network layer to determine matrix matrix multiplication, to be weighted super-matrix. 8 of the weighted super-matrix units of (normalized), seeking the powe)

说明：  基于点的位姿估计，用的是正交迭代算法，国外论文的源代码(Point-based pose estimation, iterative algorithm using the orthogonal)

基于MATLAB自编kpca和pca源程序，内附运行数据，多次运行无误。谢谢(Based on MATLAB and self kpca pca source, containing operating data, multiple runs correctly. Thank you)

最优化方面的牛顿法算法，方便入门同学学习(Newton' s method algorithm optimized with respect to the most convenient entry students learning)

基于MATLAB的遗传算法的源程序,内含交叉变异等多种方式的源码。(Based on MATLAB genetic algorithm source code, including crossover and mutation of the source of a variety of ways.)

由于信号在传播过程中，由于接收机的移动，就会产生多普勒频移，该文件先分析了多普勒滤波器的频响以及对多普勒频移进行了仿真(Due to the signal in the propagation process, due to the movement of the receiver, and will produce the Doppler shift, the file is first analyzed the frequency response of the Doppler filter and the Doppler shift the simulation)

说明：  用Matlab实现多目标遗传算法的源代码(Multi-objective genetic algorithm source code)

this program implement barbershop in c++

1、系统仅处于训练状态。训练序列为2cos(2π×f1×n/fs)， 干扰为sin(2π×f2×n/fs)；序列长度为100个样点。 其中n=0…99，f1=1kHz，f2=2kHz，fs=8kHz。 2、采用LMS算法，均衡器输入为训练序列加上干扰，均衡器阶数为21阶，步长因子β=0.01。 3、在Matlab中编写浮点LMS算法，绘制均衡器的输出波形，并与训练序列进行对比。 (1, the system only in the training status. The training sequence is 2cos (2πf1n/fs), interference sin (2πf2n/fs) sequence length of 100 samples. Where n = 0 ... 99, f1 = 1kHz, f2 = 2kHz, fs = 8kHz. 2, using LMS algorithm, the input to the equalizer training sequence plus interference equalizer order is 21 bands, step factor β = 0.01. 3, the preparation of the floating-point LMS algorithm in Matlab, draw the output waveform equalizer, and with the training sequence comparison.)