51asmExample

此程序为CRT显示器的IIC总线的驱动，主芯片为MYSON公司的MTV212MN64(This procedure for the CRT display IIC bus driver, the main chip for Myson' s MTV212MN64)

说明：  可以通过图片制作自己想要的东西,大家可以自己制作U盘。(You can make what you want through pictures, and you can make your own U disk.)

stm32对于rn8209d直流电表上的应用驱动，包含电表校表过程，参数保存与上电取出！(STM32 for the rn8209d DC meter application drive, including the meter reading table process, parameter saving and power out!)

超声波测距模块DHT11的学习资料和STM8控制下的程序。(Ultrasonic ranging module under the control of learning materials and STM8 DHT11 program.)

根据设计任务书的要求，本次设计为110kV 变电站电气一次部分初步设计，并绘 制电气主接线图及其他图纸。该变电站设有两台主变压器，站内主接线分为110kV、 35kV 和10kV 三个电压等级。各个电压等级分别采用单母线分段接线、单母线分段带 旁母接线和单母线分段接线(From the guide of engineering design assignment, we have to design primary power-system of 110kV substation and draw main electrical one-line diagram and others. There are two main transformer in the substation in which main electrical connection can be divided into three voltage grades: 110kV, 35kV with 10kV.It deposits sectionalized single bus bar scheme, sectionalized single and transfer bus bar and sectionalized single bus bar scheme per grade.)

用keilC 开发的基于nRF24LE1的wifi收发程序，已经用于实际数据传输系统(keil C wifi nRF24LE1)

基于keil软件的51单片机程序，18B20测温及12864液晶显示的文件。晶振为12M(Based on the the keil software 51 microcontroller procedure 18B20 temperature measurement and 12864 LCD file. Crystal-12M)

ADC C++ for 9S12XS128 FREESCALE

相比于传统使用的电机，永磁同步电动机（PMSM）具有着比较高的工作效率、比较高的力矩惯量比、比较高的能量密度和环保节能等优越特性，所以对永磁同步电机进行控制调速方面的研究有着相当重要的意义。我们设定电机转速初始值作为给定值，然后与反馈的实际值进行比较，得到的差值输入PI控制器进行控制，得到交轴电流。同时三相绕组输出的电流经过clarke变换和park变化得到电流的实际值，分别与给定值进行比较，将比较后的值再进行park转换，得到的结果经过SVPWM技术调制之后输入到逆变器，继而可以驱动三相电机。(Used compared to traditional motor, permanent magnet synchronous motor (all-digital fuzzy) has a higher efficiency, higher moment of inertia ratio, higher energy density and superior properties such as environmental protection and energy saving, so the control of permanent magnet synchronous motor speed regulation research has important significance. We set the initial value of motor speed as the given value, and then compare it with the actual value of feedback. The difference obtained is input to PI controller for control, and the current of crossaxis is obtained. At the same time the output three-phase winding current through Clarke transformation and park changes the current actual value, compared with a given value respectively, after comparing the value of the park transformation again, the result after SVPWM modulation technology input to the inverter, which in turn can drive three-phase motor.)

说明：  单片机软件仿真开发的硬件级联方式，可用于简单仿真及硬件实现(SCM software simulation developed hardware cascade can be used for simple simulation and hardware implementation)