emd

lists all possible ways to permute k elements out of the vector v, with replacement.

matlab 程序汇编学习课程 上 自学matlab的最好资料(matlab study)

具有参考信号的独立分量分析程序，国外的提出这个问题的人编写的。(Independent component analysis (ICA) program with a reference signal abroad website.)

MIMO-OFDM系统中不同信道估计的对比程序(MIMO-OFDM system comparison of different channel estimation procedures)

说明：  根据前人研究成果可以证明，煤镜质组反射率各向异性对煤田构造特征具有指示意义，镜质组最小反射率可以指示构造主应力方向。然而，在实际测量中，如何得到真正的镜质组最大、最小反射率及其方位是其中的关键环节。利用现有的岩石有限应变椭球拟合方法进行镜质组反射率椭球体拟合不失为一种行之有效的方法，可以由此确定镜质组最大、最小、中间反射率及其三维空间方位。 将之前拟合得到的反射率椭圆看作岩石有限应变椭圆即二维应变，其由之前的统计方法测定得到，三个截面的数据对于拟合唯一应变椭球来说是过多的，因此不可避免出现误差，导致三个截面应变椭圆不通过同一个椭球的情况。为了从三个截面数据得到唯一的应变椭球，需要对得到的数据进行相容性调整。采用Oertel的方法，从每一测量参数在不同截面中的值是正态分布这一假定出发，利用加权最小二乘法进行误差调整。(According to results of previous studies may prove vitrinite reflectance anisotropy on structural characteristics have implications for coal, vitrinite reflectance may indicate tectonic minimum principal stress directions. However, in actual measurement, how to get real vitrinite maximum, minimum reflectivity and its orientation is the key link. Conduct vitrinite reflectance ellipsoid fitting regarded as a proven method using existing rock finite strain ellipsoid fitting method can thus determine vitrinite maximum, minimum, intermediate reflectance and dimensional spatial orientation . Before fitting the reflectance of finite strain ellipse oval rock that is seen as a two-dimensional strain, as determined by statistical methods which have been before the data fit only for the three sections of the strain ellipsoid is excessive, and therefore can not to avoid errors, resulting in three elliptical cross-section does not pass through the same strain ellipsoid situation. In order to obtai)

改程序的功能：基于IMAGE混响模型编写的混响估计程序，条件实在矩形的房子中进行的(Change program features: based on IMAGE reverberation model reverberation estimation program written, just rectangular house)

MATLAB中SIMULINK模块的教程(SIMULINK module in MATLAB Tutorial)

精通MATLABGUI设计全书源代码。这是使用matlab完成gui设计的一本好书。毕竟有时候用一下gui还是可以省下很多工作时间的(The book source code versed in MATLABGUI design)

使用matlab软件，并利用三次样条插值法 求信号的包络线 源代码(Use matlab software, and use cubic spline interpolation method the signal envelope source code)

kfcm，为模糊核聚类算法，用于将低维的数据映射到高维进行分类，是较先进的算法(kfcm, the fuzzy kernel clustering algorithm for low-dimensional data is mapped to high-dimensional classification, is a more advanced algorithms)