UDPChattool

说明：  关于Socket编程的实例，希望可以给大家提供一定的参考(Socket Programming for example, we hope to provide some reference)

一套完整的在线升级程序，只需修改配置文件即可成为自己的升级程序。(A complete set of online upgrade program, simply modify the configuration file to become their own upgrade process.)

通信工程师电信网络专业习题集 通信工程师电信网络专业习题集 通信工程师电信网络专业习题集(CommunicationEngineerNetWorkPractise CommunicationEngineerNetWorkPractise CommunicationEngineerNetWorkPractise)

实现单线程文件传输，不支持断点传出，功能相对简单，但是性能很好。(Achieve single-threaded file transfer, does not support breakpoints spread, function is relatively simple, but the performance is very good.)

ava 框架，以前找的，不知道现在能用不，需要的自己下载(ava kuangjia )

VC++网络连接监控程序源代码，适合编写网络监控的编程者参考，选择监听的网络IP地址后才可以开始监听里程。并包括了IDS过滤器参数设置，几点提示： 　　1.初始状态只监听连接,不捕获IP数据 　　2.鼠标右击列表选择或取消监控某端口数据 　　3.为防止ping攻击,一般情况ping数据全部监控 　　4.监控某端口数据时,不监控ping包 　　5.数据超过20k将被清空 　　6.右边窗口停止抓包后显示十六进制数(VC++ source code network connection monitoring, network monitoring program for the preparation of reference, select the monitor s network IP address before you can start listening mileage. And includes IDS filter parameter settings, a few tips: 1. Initial state only listen for connections, do not capture IP data 2 Right-click the list to select or deselect a port monitoring data 3 To prevent ping attacks, general ping all monitoring data 4 When a port monitoring data, no monitoring of ping packets 5 The data will be cleared over 20k 6 right window displays the hexadecimal number stopped after capture)

编写程序，实现基于ARP协议获取本局域网内全部活动主机MAC地址与IP地址对应关系列表，要求使用Winpcap，手动封装ARP数据包，并实现ARP响应数据包的接收和解析。(programming, ARP-based LAN access to the activities of all MAC address and IP address correspondence list, require the use of Winpcap, manual Packaging ARP packets, and achieve ARP response data packet reception and analysis.)

中频感应加热以其加热效率高、速度快，可控性好及易于实现机械化、自动化等优点，已在熔炼、铸造、弯管、热锻、焊接和表面热处理等行业得到广泛的应用。 本设计根据设计任务进行了方案设计，设计了相应的硬件电路，研制了20KW中频感应加热电源。 本设计中感应加热电源采用IGBT作为开关器件，可工作在10 Hz～10 kHz频段。它由整流器、滤波器、和逆变器组成。整流器采用不可控三相全桥式整流电路。滤波器采用两个电解电容和一个电感组成Ⅱ型滤波器滤波和无源功率因数校正。逆变器主要由PWM控制器SG3525A控制四个IGBT的开通和关断，实现DC-AC的转换。 设计中采用的芯片主要是PWM控制器SG3525A和光耦合驱动电路HCPL-316J。设计过程中程充分利用了SG3525A的控制性能，具有宽的可调工作频率，死区时间可调，具有输入欠电压锁定功能和双路输出电流。由于HCPL-316J具有快的开关速度（500ns），光隔离，故障状态反馈，可配置自动复位、自动关闭等功能，所以选择其作为IGBT的驱动。 对原理样机的调试结果表明，所完成的设计实现了设计任务规定的基本功能。此外，为了满足不同器件对功率需要的要求，设计了功率可调。这部分超出了设计任务书规定的任务。(induction heating with high heating efficiency, speed and good controllability and easy to mechanization. the advantages of automation, in melting, casting, bending, forging, welding and surface heat treatment and other industries have been widely employed. According to the design tasks for the design of the program design, design corresponding to the hardware circuit, Development of 20 KW induction heating power. The design of induction heating power IGBT used as a switching device, which can work in 10 Hz- 10 kHz frequency band. It consists of rectifier, filter, and the inverter components. Controlled Rectifier not use the entire three-phase bridge rectifier circuit. 2 filter used an electrolytic capacitor and inductor components II-type filter and passive PFC. Inverter mainly by the PW)

c++经典代码大全，适合初学者下载参考使用。(c++ Guinness classic code, suitable for beginners reference.)

用于将网络边关系转换成matlab可用的临近矩阵。(Used to convert the network edge into matlab available close relationship matrix.)