crack

matlab遗传算法程序 讓你更瞭了解 遺傳的結構 和 算法 (genetic algorithm matlab program allows you to better understand the structure and genetic algorithm)

一个二阶中心插值滤波器（DDF2）的目标跟踪仿真实例。(a second center interpolation filter (DDF2) target tracking simulation example.)

基于Hilbert包络解调及倒谱分析法，在LabVIEW平台开发的齿轮箱故障诊断程序(Based on Hilbert envelope demodulation and cepstrum analysis, the gearbox fault diagnosis program developed on the LabVIEW platform)

基于圆阵和线阵的SIM算法和正交化算法。程序上的区别在于导向矢量的不同(Based on the circle array and linear array SIM algorithm and are orthogonal algorithm )

在网上收集的，讲述如何使用simulink环境下SimSystemBlockset中各个模块。(Collected online about how to use simulink environment SimSystemBlockset in each module.)

采用最速下降法的AGC仿真，比较了用误差平均和仅用当次误差的控制效果。(The steepest descent method using the AGC simulation, compared with the average error, and only when the second error control effect.)

BPSK调制下的2发一收空时分组码程序，本程序是对两发一收情况下采用空时分组码的性能分析，星座映射采用的是BPSK映射，接收天线上的接收信噪比，在仿真的过程中把接收信号的功率归一化为1(BPSK modulation issued a collection of two space-time block code program)

This file gives the main function for the implementation of the hybridized version of the cuckoo search algorithm by combining it with the Nelder Mead Simplex algorithm. The method is designed to minimize functions with a low number of dimensions in a low number of iterations.

用局部参数最优化方法设计一个模型参考自适应系统,可调增益的初值Kc(0)=0.2，给定值r(t)为单位阶跃信号，即r(t)=A×1(t)。 要求： 1把连续系统离散化(采样时间可取0.1)。 2编制并运行这个系统的计算机程序(注意调整B值，使系统获得较好的自适应特性)。 3记录ym、yp的曲线 记录kp×kc的曲线 记录广义输出误差e的变化曲线。 4在参数收敛后，让Kp=2变为Kp=1，重新观察Kp×Kc及e的变化曲线。 5找出在确定的B值下，使系统不稳定的A值(阶跃信号的幅值)，并与用劳斯稳定判据计算的结果比较。 (With local parameter optimization method to design a model reference adaptive system, adjustable gain initial Kc (0) = 0.2, for a given value of r (t) for the unit step signal that r (t) = A × 1 ( t). Requirements: a continuous system discretization (sampling time of 0.1 preferred). 2 compiled and run the system computer program (Note B to adjust the value of the system to obtain better adaptive characteristics). 3 records ym, yp curve record kp × kc curve records generalized output error e curves. 4 parameter convergence, let Kp = 2 into the Kp = 1, re-observed Kp × Kc and e curves. B-5 to find value in determining the next, making the system unstable A value (step signal of amplitude), and using Routh stability criterion and the comparison of the results calculated.)

nordig channel simulation