LM_huffman

外国的一个大牛写的ply格式模型的读写程序，注释很详细，和适合学习(A large foreign cattle write ply format model reading and writing program notes in great detail, and suitable for learning)

关于数字图像处理中的ssda模板匹配方法。程序实现在指定图像中生成一个大小固定的矩形区域，然后用模板匹配法找出矩形位置。使用SSDA算法实现。包括源程序、待处理图像以及运行结果截图。(On digital image processing ssda template matching method. Procedures to achieve the specified image to generate a fixed size rectangular region, and then position the template matching method to find the rectangle. Using the SSDA algorithm. Including source code, pending results of the image and run shots.)

说明：  应用在认知无线电频谱检测中。环境：经过加性白噪声的信号。功能：求解虚警概率和漏检概率。(Used in cognitive radio spectrum detection.Environment: after additive white noise signal.Function: to solve the false alarm probability and missed detection probability.)

matlab编写的适用于数值分析求解线性方程组的程序(matlab numerical analysis prepared for the procedure for solving linear equations)

数字助听器回声消除采用自适应回声消除算法。NLMS算法的得到了很大的应用，matlab仿真程序，很有用(Digital hearing aids in the NLMS echo cancellation algorithm MATLAB simulation program, oh well )

模糊控制器：利用matlab建立复杂的模糊规则。既可以编写程序实现，也可以使用matlab自带fuzzy工具箱完成。(Fuzzy controller: use matlab to create complex fuzzy rules. Can realize the preparation of procedures, you can also use its own fuzzy toolbox matlab completed.)

跳频系统仿真 基于matlab simulink的源程序，包括框图(Frequency hopping system simulation based on matlab simulink source, including block diagram)

说明：  切削力建模,仿真以及优化依据Altintas machining automation(cutting force modeling)

说明：  升压转换器是一种DC / DC电源转换器，可将电压从其输入（源）升至其输出（负载）。在连续导通模式下（流经电感的电流永远不会降为零），升压转换器的理论传递函数为： 占空比在哪里0.5 在此示例中，转换器从250 V电源馈送RC负载，并且PWM频率设置为31 kHz。 模拟 运行仿真并观察示波器上的波形。确认负载电压（Vout）的平均值非常接近理论值：Vout = 250 /（1- 0.5）= 500V。(A boost converter is a DC/DC power converter which steps up voltage from its input (source) to its output (load). In continuous conduction mode (current through the inductor never falls to zero), the theoretical transfer function of the boost converter is: where is the duty cycle.0.5 In this example, the converter is feeding an RC load from a 250 V source and the PWM frequency is set to 31 kHz. Simulation Run the simulation and observe waveforms on Scope. Verify that the mean value of the load voltage (Vout) is very close to the theoretical value of: Vout = 250 / (1 - 0.5) = 500 V.)

简要阐述了遗传算法的基本原理,探讨了在MATLAB 环境中实现遗传算法各算子的编程方法, 并以一个简单的实例说明所编程序在函数全局寻优中的应用。(Briefly describes the basic principles of genetic algorithms discussed in the MATLAB environment to achieve each operator genetic algorithm programming methods, and a simple example illustrates the functions programmed in the application of global optimization.)