登录
首页 » matlab » MidpointLine2

MidpointLine2

于 2009-04-19 发布 文件大小:1KB
0 279
下载积分: 1 下载次数: 30

代码说明:

  计算机图形学中点画线算法matlab实现(Computer Graphics in the realization of stipple line algorithm matlab)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • doc
    模型参考自适应程序。用于无速度传感器,做矢量控制(matlab)
    2009-04-11 15:09:01下载
    积分:1
  • Eigenface-based-face-recognition
    说明:  基于特征脸和K-L变换的人脸识别系统,人脸识别方面的基本方法(Feature-based face recognition systems and KL transform, the basic method of face recognition)
    2011-03-01 16:29:35下载
    积分:1
  • unit-commitmentdynamic
    code for unit commitment problem power system analysis
    2015-04-10 00:37:06下载
    积分:1
  • zy1
    萤火虫算法在分布式电源优化配置中应用 全部 很好的程序 只需换换节点数目就可以(Firefly algorithm optimization in distributed power configuration in all a very good application program can only change of the number of nodes)
    2020-11-23 23:29:33下载
    积分:1
  • seg4
    segmentation tools for segmention lazy snaping
    2009-06-19 18:04:18下载
    积分:1
  • SIMULACIONES
    MULTIAGENTS 4 AGENTS, FORMATION PROBLEM
    2013-08-25 14:42:29下载
    积分:1
  • simulator
    MATLAB Simulation of OFDM Transmitter and Receiver
    2010-06-14 04:05:11下载
    积分:1
  • BusInc
    Y bus incident for load flow analysis
    2011-08-09 02:06:57下载
    积分:1
  • Dvr-linear-harmonics
    This paper describes the problem of voltage sags and swells and its severe impact on non linear loads or sensitive loads. The dynamic voltage restorer (DVR) has become popular as a cost effective solution for the protection of sensitive loads voltage sags and swells. The control of the compensation voltages in DVR based on dqo algorithm is discussed. It first analyzes the power circuit of a DVR system in order to come up with appropriate control limitations and control targets for the compensation voltage control. The proposed control scheme is simple to design. Simulation results carried out by Matlab/Simulink verify the performance of the proposed method.
    2014-10-09 01:24:00下载
    积分:1
  • exp4
    把激光陀螺捷联惯导系统和GNSS接收机固联于实验车实验仓中,接收机天线固联在实验车实验仓上方,车载计算机实时接收和采集惯导系统、卫星导航接收机的原始数据,在郊外开阔公路进行车载实验。 通过matlab编程实现卫星导航伪距单点定位、INS/GPS松组合导航的全过程。 1)卫星导航单点定位测速:利用采集得到的接收机时间、伪距、多普勒频移数据,要求进行单点定位、测速解算,输出接收机的位置、速度随时间的变化曲线,并给出位置、速度误差曲线; 2)松组合导航:结合惯导解算和卫星接收机单点定位测速,要求采用Kalman滤波器实现惯导/卫星位置、速度组合导航解算,滤波器维数至少包括惯导的位置、速度、姿态角9维。将组合导航后的姿态角与纯惯导的姿态角进行对比分析,给出位置、速度误差曲线。(The laser gyro strapdown inertial navigation system and GNSS receiver are fixed in the experimental compartment of the experimental vehicle. The antenna of the receiver is fixed above the experimental compartment of the experimental vehicle. The on-board computer receives and collects the original data of the inertial navigation system and satellite navigation receiver in real time, and carries out on-board experiments on the suburban open highway.)
    2021-03-25 17:19:14下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载