Nucleus系统介绍文档，其中介绍了实时系统的任务处理与抢占处理等。...

这是针对 Linux (i386)平台的 minigui 3.6.2 开发包（MiniGUI-Processes 运行模式）。-This is for Linux (i386) platform minigui 3.6.2 Development Kit (MiniGUI-Processes running mode).

优龙FS2410板的I2C通信源码，可以实现s3c2410 的I2C通信,开发平台为ADS1.2。-Liuzhou excellent FS2410 board I2C communication source, the S3C2410 can realize I2C communications, development platform for ADS1.2.

一个机器人提足球的代码!基于神经网络! 一个机器人提足球的代码!基于神经网络!-a robot soccer mention the code! Based on neural network! A robot soccer mention the code! Based on neural network Liaison!

lpc2200 ad 转换器的驱动代码。在uclinux下编译使用。-lpc2200 ad code converter drive. Under uclinux compiler in use.

The objective is to set up SPI communication between VTI Technologies digital pressure sensor component and an MCU of an application device ATMEGA16L. In this code example: ?The MCU is configured ?SCP1000-D01 is initialized and configured ?The high resolution measurement mode is activated ?Temperature and pressure information is read always when the DRDY pin is in high state Please refer to the document "SCP1000 Product Family Specification 8260800" for further information on SCP1000 register addressing and SPI communication. This document applies to the SCP1000-D01.-The objective is to set up SPI communication between VTI Technologies digital pressure sensor component and an MCU of an application device ATMEGA16L. In this code example: ?The MCU is configured ?SCP1000-D01 is initialized and configured ?The high resolution measurement mode is activated ?Temperature and pressure information is read always when the DRDY pin is in high state Please refer to the

AT91SAM7S256-USB-CDC for IAR5

该程序模块详细介绍了自定义缓存模块FIFO的设计过程，正在学习自定义ＦＩＦＯ模块并挂载在ａｖａｌｏｎ总线上用作缓存的读者可参考该程序。

用LCD显示器的计算器，可以进行简单的确加减乘除-Calculator with LCD display, can be really simple calculation

应用背景 所有红外遥控器的输出都是用编码后串行数据对38～40kHz的方波进行脉冲幅度调制而产生的。如果直接对已调波进行测量，由于单片机的指令周期是微秒（μs）级，而已调波的脉宽只有20多μs，会产生很大的误差。因此先要对已调波进行解调，对解调后的波形进行测量。红外遥控接收芯片CX20106可以完成对遥控信号的前置放大、限幅放大、带通滤波、峰值检波和波形整形，只需加上简单的外围电路即可完成对已调波的解调 关键技术 用红外转发器控制电器，首先要进行对码，把要控制的家电遥控器对准红外转发器，把遥控器的功能键学习到红外转发器中，学习成功后，就可以控制了，例如，学习了空调遥控器的开、关，用POLYHOME智能主机操作空调开，主机发出射频信号到红外转发器，红外转发器把射频信号转成红外信号的“开”发射出去，就能把空调打开了，射频可以穿墙，红外信号是不能穿墙的，这就能实现远距离控制电器。

linux驱动程序-linux drivers