atmega8的关于LED的代码，我自己写的，晶振是11.0592M的。

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

利用单片机实现三相电源的相序检测 利用单片机实现三相电源的相序检测-Realize the use of single-chip three-phase power supply phase sequence detection using single-chip realization of three-phase power supply phase sequence detection

本方法的基本思想就是利用单片机具有的PWM端口，在不改变PWM方波周期的前提下，通过软件的方法调整单片机的PWM控制寄存器来调整PWM的占空比，从而控制充电电流-The basic idea of this method is the use of microcontroller has the PWM ports, without changing the PWM square wave cycle, under the premise of the method to adjust by software MCU PWM control registers to adjust the PWM duty cycle and thus control the charge current

用61位单片机与C程序实现语音复读功能！-With 61 single-chip microcomputer with C program features voice repetition!

keil c51平台,此代码可用于学习TFT LCD TV 搜台等,(本人自己修改) -keil c51 platform, this code can be used to study seized Taiwan TFT LCD TV and so on, (my own modifications)

LT_1B msp430开发板例子程序－SoftwareF-LT_1B msp430开发板例子程序－SoftwareFLL

STC单片机IO口模拟RS232测试程序,Keil Cx51应用开发技术中的程序主要的功能是在利用串口调试工具发送一个8bit的数据，而后单片机接收后把这个数据发送给模拟串口-STC Single-chip analog IO port RS232 test procedures, Keil Cx51 technology application development process is essentially the function is in the use of serial debug tools send an 8bit data, and then after the single-chip receive the data sent to the simulation of serial

单片机程序，计算开关次数并保存次数，并能调用显示时间，清除纪录。-Single-chip process, calculating the number and save the number of switches, and can call the show time to clear the record.

美国达拉斯温度传感器DS18B20的温度数值转化程序。-Dallas DS18B20 the temperature into numerical procedures.

本文是关于单片机，详细介绍了51单片机的交通灯设计，希望大家提供意见。-This article is about the single-chip, detailing 51 SCM design of traffic lights, I hope to advise the U.S..