USB program,c language realization,

本人调试通过的串口通信程序,对初学者有一定的参考价值-I debugging through the serial communication program for beginners with some reference value

串行口是计算机一种常用的接口，具有连接线少，通讯简单，得到广泛的使用。常用的串口是RS-232-C接口(又称EIA RS-232-C)它是在1970年由美国电子工业协会(EIA)联合贝尔系统、调制解调器厂家及计算机终端生产厂家共同制定的用于串行通讯的标准。它的全名是"数据终端设备(DTE)和数据通讯设备(DCE)之间串行二进制数据交换接口技术标准"该标准规定采用一个25个脚的DB25连接器，对连接器的每个引脚的信号内容加以规定，还对各种信号的电平加以规定。传输距离在码元畸变小于4%的情况下，传输电缆长度应为50英尺。 　　Linux操作系统从一开始就对串行口提供了很好的支持，本文就Linux下的串行口通讯编程进行简单的介绍.-computer serial port is a common interface, with connecting lines, simple communications, to be widely used. It is commonly used serial RS-232-C interface (also known as the EIA RS-232-C) it is in 1970 by the American Electronics Industry Association (EIA) Joint Bell System, a modem manufacturers and computer terminal manufacturers developed for serial communication standards. Its full title is "data terminal equipment (DTE) and data communications equipment (DCE) between serial binary data exchange interface technology standards," the use of a standard 25 feet to the DB25 connector, the connector pin of each signal content requirements, but also the right signal--

使用Delphi编写的串口通信控制器，具备文件传输功能-prepared by the use of Delphi serial communication controller with the file transfer function

具有语音自动应答功能的串口程序-with automatic voice response function of the Serial procedures

介绍了如何用verilog语言实现处理器部件uart-Describes how to use Verilog language processor components UART

getmywish使用的usb注意：由于用到多串口控制，需要在收到数据时确定是哪个串口来的数据。 下面是串口事件处理函数代码： -getmywish use usb Note : As used Multiport Serial control, the receipt of necessary data to determine which of the serial data. Below are the serial code incident handling functions :

一个包含了几乎所有串口操作的源码群，可以根据自己需要改写-1 contains almost all serial-source operating groups, according to their own needs rewriting

简要描述： 一个很好而小巧的串口调试助手，支持常用的300-115200bps波特率，能设置校验、数据位和停止位，能以ASCII码或十六进制接收或发送任何数据或字符（包括中文），可以任意设定自动发送周期,并能将接收数据保存成文本文件，能发送任意大小的文本文件。-Briefly described: a good and compact serial debugging assistant to support commonly used 300-115200bps the baud rate, parity can be set up, data bit and stop bits are used in the hexadecimal ASCII code or receive or send any data or characters (including Chinese), can set up automatic send cycle, and can receive data into a text file that can send any size text file.

WAPI串口编程示例,用复杂的api函数,实现的串口功能更为强大.-WAPI serial programming examples, the api with complex functions, to achieve the serial function more powerful.

讲述串口通信编程,vc实现！多线程，异步方式。-about serial communication programming, vc achieve! Multi-threaded, asynchronous mode.