MCS

单个或多个ds1820温度读取c51源程序-single or multiple ds1820 temperature read source decoder

nRF24E1多发单收，接收程序。原理，切换接收频率。-nRF24E1 multiple single-admission, to receive the procedure. Principle, to switch the receiving frequency.

本文给出了一种以80C31为主控CPU的固定电话短信息终端的设计，从系统软硬件两个方面说明了固定电话短信息终端的设计方法和各个部分的工作原理 -This paper proposes a 80C31 CPU for controlling the fixed telephone short message terminal design, system software and hardware from the two showed that the fixed telephone short message terminal design methods and various parts of the work principle

进行51单片机主控智能车模块测试时用光电管返回的道路信息控制舵机以一定角度转向。-Intelligent control for 51 single-chip module test vehicle with photocell control to return to the road information to a certain point of gear shift.

DTMF编码芯片HT9200的51接口程序。输入参数R2表示发送数据个数，输入数据与发送数据与DTMF码的关系:00H-0 01H-1 02H-2 03H-3 04H-4 05H-5 06H-6 07H-7 08H-8 09H-9 0AH-A 0BH-B 0CH-C 0DH-D 0EH-* 0FH-#。详细说明参考文件内-DTMF encoder chip HT9200 51 interface program. R2 said input parameters to send data distribution, data entry and send data with the DTMF code : 00H-0 01H- 02H-2 Mr- 3 in the 04H-4 05H-5 06H-6 07H-7 08H-8 7-9 0AH-A 0BH- 0CH B-C 0DH-D 0EH-* 0FH-#. Detailed information paper

AVR mega8 单片机操作CC1100的例子-AVR mega8 MCU and CC1100 RF IC

基于DS18B20的温度计，用C51编程 时钟控制的很精确，调试成功的程序，没有问题，可以很方便的移植-Based on the thermometer DS18B20 with C51 programming clock control is very accurate, debugging successful procedures, there is no problem, you can easily transplant

上位机采用vb编程,实现与多台s7200的自由口通信.-Host computer using vb programming, with more than the freedom of the mouth communication s7200.

单片机P1口与4个按键连接，用于信号幅度和频率调节操作键。单片机P0、P2.7、P3.6(-WR)与DA0832、2个741(运放)连接构成波形信号输出电路。 编程使波形信号输出电路输出正弦波信号，并且可通过操作键调节信号的幅度和频率。幅度和频率调节级别从0~10，共11个等级。 -Singlechip P1 I connect with the four buttons for the signal amplitude and frequency adjustment operation keys. Singlechip P0, P2.7, P3.6 (-WR) and DA0832, 2 months 741 (operational amplifier) to connect constitute waveform signal output circuit. Programming so that waveform signal output circuit output sine wave signal, and can be operated keys adjust the signal amplitude and frequency. Amplitude and frequency adjustment level from 0 ~ 10, a total of 11 grades.

这是一个单片机键盘响应程序，主要用于单片机设计中对键盘的编程，使得单片机能够显示键盘的按键-This is a microcontroller keyboard response procedures, mainly for the design of single-chip microcomputer keyboard programming, SCM makes the keyboard can display buttons