-
这是一个java类 这是一个java类 这是一个java类
这是一个java类 这是一个java类 这是一个java类 -This is a java-type This is a java-type This is a java-type This is a java-type This is a java-type
- 2022-02-03 19:17:04下载
- 积分:1
-
This procedure is a direct sequence spread spectrum packet simulation. Need matl...
本程序是一个直接扩频序列仿真包。需要matlab中安装了simulink才可以使用。-This procedure is a direct sequence spread spectrum packet simulation. Need matlab installed can only be used simulink.
- 2022-04-29 16:38:30下载
- 积分:1
-
售票系统代码及设计思想。本程序是我的一个课程设计,得到老师的肯定了。请放心,绝对原创!...
售票系统代码及设计思想。本程序是我的一个课程设计,得到老师的肯定了。请放心,绝对原创!-ticketing system code and design ideas. This program was one of my curriculum design, be sure the teacher. Please be assured that absolute originality!
- 2022-07-12 09:43:48下载
- 积分:1
-
OFDM宽带无线系统的链路级的仿真程序(多天线,QAM调制,编码,合并)等等很齐全)...
OFDM宽带无线系统的链路级的仿真程序(多天线,QAM调制,编码,合并)等等很齐全)-OFDM broadband wireless system link-level simulation program (multi-antenna, QAM modulation, coding, combined) and so very full)
- 2023-03-05 12:15:03下载
- 积分:1
-
CDMA系统的仿真程序,在此基础上研究了下CDMA系统等。
cdma系统的仿真程序,可以在此基础上研究cdma系统的各种环境下的性能,改程序已经验证过-cdma system simulation program, in this study based on the CDMA system under various environmental performance, change procedures have been tested
- 2022-03-15 22:28:10下载
- 积分:1
-
LabView 用于串口接收读取缓冲的最佳时间间隔
LabView 用于串口读写数据读取缓冲的最佳时间间隔,在串口通信内容长度不确定的情况下,能完整接收数据并在接收结束之后尽快的停止接收,决定串口通信的效率。此vi经过小修改应该就能普遍适用。
- 2023-02-08 06:05:04下载
- 积分:1
-
LT code in C/C++
这是用C/C++编写的LT编码和解码的代码。这是一个非常有效的大数据包代码。我们可以将其用于数据通信;
- 2022-05-29 14:49:10下载
- 积分:1
-
实现蒙特卡罗分析,可以直接调用进行对误码率等数字通信的相关参数分析...
实现蒙特卡罗分析,可以直接调用进行对误码率等数字通信的相关参数分析-The realization of the Monte Carlo analysis, can directly call on the bit error rate for digital communications, such as analysis of relevant parameters
- 2022-05-23 14:53:07下载
- 积分:1
-
litwizi j2me
litwizi j2me
- 2022-05-27 19:02:24下载
- 积分:1
-
0. Install the rp
0. Install the rp-pppoe-software
--------------------------------
You should have already done this by the time you re reading this. If not,
go back and read README.
1. Set up your Ethernet hardware
--------------------------------
First, make sure the Ethernet card you intend to use with the modem is
visible to the Linux kernel. Just how to do this is beyond the scope
of this document. However, if the card is the only Ethernet card in
the system, executing:
ifconfig eth0
should display something like this:
eth0 Link encap:Ethernet HWaddr 00:60:67:62:31:D4
plust some more lines. Your HWaddr will be different. As long as you see
the HWaddr line, your card should be working.
DO NOT assign an IP address to the Ethernet card. DO NOT configure the
card to come up at boot time.-0. Install the rp- PPPOE-software-------------------------------- You should have al ready done this by the time you re reading this. I f not, go back and rea
- 2023-03-02 00:45:03下载
- 积分:1