shenjingwangluoxuexi

upqc with model predictive control

这是MATLAB工具箱，用来实现波形的生产！(This is the MATLAB toolbox, which can be used for the production of wave!)

duda第二版 模式分类书的课后练习的全matlab仿真文件(duda s pattern classification second edition of the book exercises full matlab simulation file)

good work on Pole placement method

说明：  here is the matlab code for sixty four qam modulation

产生右图所示图像f1(m,n)，其中图像大小为256×256，中间亮条为128 ×32，暗处=0，亮处=100。对其进行FFT： ① 同屏显示原图f1(m,n)和FFT(f1)的幅度谱图； ② 若令f2(m,n)=（-1）m+n f1(m,n)，重复以上过程，比较二者幅度 谱的异同，简述理由； ③ 若将f2(m,n)顺时针旋转90 度得到f3(m,n)，试显示FFT(f3)的幅 度谱，并与FFT(f2)的幅度谱进行比较； ④ 若将f1(m,n) 顺时针旋转90 度得到f4(m,n)，令f5(m,n)=f1(m,n)+f4(m,n)，试显 示FFT(f5)的幅度谱，并指出其与FFT(f1)和FFT(f4)的关系； ⑤ 若令f6(m,n)=f2(m,n)+f3(m,n)，试显示FFT(f6)的幅度谱，并指出其与FFT(f2)和 FFT(f3)的关系，比较FFT(f6)和FFT(f5)的幅度谱。(Generating an image f1 (m, n) shown in the figure, wherein the image size is 256 256, the intermediate light bar 128 32 0 = dark, bright Department 100. Its FFT: ① screen display picture f1 (m, n) and the FFT (f1) of the amplitude spectrum ② If so f2 (m, n) = (-1) m+n f1 (m, n), repeat The above process, comparing the amplitude spectrum of the similarities and differences between the two, brief reasons ③ If f2 (m, n) 90 degrees clockwise to get f3 (m, n), try to display FFT (f3) the amplitude spectrum and with the FFT (f2) comparing the amplitude spectrum ④ If f1 (m, n) obtained by 90 degrees clockwise f4 (m, n), so f5 (m, n) = f1 (m, n)+f4 (m, n ), try to display FFT (f5) amplitude spectrum, and pointed out its relationship with the FFT (f1) and FFT (f4) of ⑤ If so f6 (m, n) = f2 (m, n)+f3 (m, n) and try to display the FFT (f6) amplitude spectrum, and pointed out its relationship with the FFT (f2) and FFT (f3), comparing FFT (f6) and FFT (f5) amplitude spectrum.)

随记减量法是从结构的随机振动响应信号中提取该结构自由衰减振动信号的一种方法-With the mind Reduction Act(Reduction Act is credited with random vibration response of the structure from the signal to extract the structure of a method-With free decay vibration signals the mind Reduction Act)

hi this is tha face detection source code from asqur

matlab inverter example

直流伺服电机用MATLAB实现的源代码，伺服系统由具有位置反馈、速度反馈和电流反馈的三闭环结构组成本控制系统采用模糊和PID复合控制，在小偏差时转化为P ID控制，这样就获得了比纯模糊控制更高的稳态精度，有比P ID控制更快的动态响应、更小的超调量。(DC servo motor to achieve with the MATLAB source code, by a position feedback servo system, the speed feedback and current feedback loop structure composed of three of the control system using fuzzy and PID compound control, in a small deviation into the P ID control, so that access to higher than the pure fuzzy control steady-state accuracy, faster than P ID control the dynamic response, smaller overshoot.)