-
3D打印机 marlin
应用背景The leading developers of Marlin are currently (January 2015) EvdZ and bkubicek, though many others contribute with their patches. This is a firmware for reprap single-processor electronics setups. It also works on the Ultimaker PCB. It supports printing from SD card+Folders, and look-ahead trajectory planning. This work is licensed under the GNU GPL v3 or (at the user"s discretion) any later version. It is based on Sprinter firmware, which was licensed under GPL v2 or later.关键技术
Features:
Interrupt based movement with real linear acceleration.
High steprate.
Look ahead (Keep the speed high when possible. High cornering speed).
Interrupt based temperature protection.
preliminary sup
- 2022-03-06 02:29:58下载
- 积分:1
-
C程序写的C8051F330和330 DS18B20的测温程序控制…
C程序写的C8051F330和DS18B20的测温程序,通过330转换成0~2mA的电流输出。-C8051F330 program written in C and the temperature program DS18B20 by 330 to convert the current output 0 ~ 2mA.
- 2022-07-18 05:00:14下载
- 积分:1
-
STK6037 源代码
STK6037源代码,系统初始化,包括IO 初始化,数码管动态扫描,PWM输出,定时器使用中断,串口485使用,产生250K适合485通信的波特率。HC595的驱动程序,经典的按键扫描,按键处理程序
- 2022-01-26 07:43:55下载
- 积分:1
-
nrf24l01 六通道接收与分时发送例程 mpu6050采集,dmp读数
nrf24l01,六通道,接收与分时发送例程,mpu6050采集,dmp读数
- 2022-07-17 04:13:10下载
- 积分:1
-
Single
单片机实信号发生,可发生正弦.方波,三角波.-Single-chip real signal can be sine occurred. Square wave, triangle wave.
- 2022-01-31 20:26:00下载
- 积分:1
-
步进电机的单片机控制系统的设计用C语言编写的程序,可以直接使用...
步进电机的单片机控制系统的设计用C语言编写的程序,可以直接使用-Stepper motor microcontroller control system design using C language program can be used directly
- 2022-07-23 01:37:51下载
- 积分:1
-
INTERFACING 24LC64 EEPROM WITH AT89C51 MICROCONTROLLER
24LC64 EEPROM与AT89C51的接口
- 2022-07-20 22:54:52下载
- 积分:1
-
IAR 环境 LPC2478 PWM 程序
IAR 环境 LPC2478 PWM 程序-IAR environment LPC2478 PWM process
- 2022-05-22 22:32:38下载
- 积分:1
-
MPC860初始化QMC在HDLC模式示例
MPC860初始化QMC在HDLC模式示例-MPC860 initialization QMC in HDLC model example
- 2023-01-23 13:30:04下载
- 积分:1
-
OMB COMMON CLASSES 源代码
OMB COMMON CLASSES 源代码-OMB COMMON CLASSES source code
- 2023-02-09 11:55:04下载
- 积分:1