基于空域和频域的迭代盲复原算法MATLAB编程

说明：  基于FFT的谐波检测,采用快速傅里叶算法后得到原始波形中各次分量的频率和幅值特性，从中可以直接观测出各次谐波分量的频率和幅值信息. 程序1采用快速傅里叶算法后得到原始波形中各次分量的频率和幅值特性图 程序2输入信号经过FFT变换得到的频谱特性图 程序3对输入信号进行采样，应用一维小波变换函数进行三层小波分析(Based on FFT harmonic detection, the frequency and amplitude characteristics of each harmonic component in the original waveform are obtained by using fast Fourier algorithm, from which the frequency and amplitude information of each harmonic component can be directly observed In program 1, the frequency and amplitude characteristics of each component in the original waveform are obtained by using the fast Fourier algorithm The spectrum characteristic diagram of program 2 input signal through FFT transformation Program 3 samples the input signal and applies one-dimensional wavelet transform function to three-level wavelet analysis)

资源描述MATLAB中实现PID控制系统的，改变输入r(k）分别为阶跃信号、三角波、方波。

感知准则梯降法求线性判别函数权向量的算法(using perceptual criterion to find weightvector of a linear decision function)

说明：  高压共轨系统模型，包括喷油器，油泵，共轨(High pressure common rail system model, including injector, oil pump, common rail)

空间目标识别，采用PM算法，研究生时的现代信号处理的作业，非归零型差分相位调制信号建模与仿真分析 ，FIR 底通和带通滤波器和IIR 底通和带通滤波器，独立成分分析算法降低原始数据噪声，加入重复控制。

程序主要包括：1．MyInit.m 数据初始化 输出参数： XTrueZ 目标真实轨迹 Z0 目标观测值 T 采样周期 Q 系统误差阵 DeltaR 距离误差 DeltaSita 方位角误差 DeltaBeta 俯仰角误差 totaltime 运动时间 montimes 蒙特卡罗仿真次数 2． EKF.m [Z1]= EKF Z1: 输出EKF滤波后结果 3. CMKF.m [Z2]= CMKF Z2: 输出CMKF滤波后结果 4. GetR.m CMKF算法中误差阵R的计算 5． CompareEandC.m EKF和CMKF、最小二乘滤波后结果比较 部分绘图代码不全，具体结果请参见 信号实验作业.doc 文档 6．source.m 产生带野值的数据 7. RemoveWilddata.m 野值剔除算法 (Procedures will include: 1. MyInit.m initialization data output parameters: XTrueZ target the real target trajectory Z0 sampling period T observed value Q system error array DeltaR distance error DeltaSita azimuth error DeltaBeta pitch angle error totaltime exercise time montimes the number of Monte-Carlo simulation 2. EKF.m [Z1] = EKF Z1: Output EKF filtered results 3. CMKF.m [Z2] = CMKF Z2: Output CMKF filtered results 4. GetR.m CMKF algorithm for the calculation of error R array 5. CompareEandC.m EKF and CMKF, least-squares filtering Comparison of part of the drawing code after the failure, specifically the results of experimental work, see the signal. Doc document 6. source.m generate the data with outliers 7. RemoveWilddata.m outliers removed Algorithm)

该算法可以反演计算二维地质模型的表面重力值和重力异常(The algorithm can calculate the surface gravity two-dimensional geological model and gravity anomaly)

说明：  用于深度置信初步描述，适合初学者进行学习(Preliminary description of applicable depth confidence, initial learning)

资源描述这是一个实现超像素图像分割的程序代码，该代码是一个benchmark类型的，能随意扩充里面的超像素图像分割算法，而且有鲁棒性的平均标准，很值得推荐下载

modulation and deodulation curves for different modulation schemes