S08例程：本程序是I/O模块的例程，所用资源为单片机通用IO接口，所接器件为LED灯， 其中D2与PTA0，D3与PTA1相连接！

LINUX设备驱动程序第三版，中文版,很适合驱动开发者-LINUX DEVICE DRIVER 3 chinese

c8051f310开发板例程，非常详细，可直接运行

实用电子钟,为六位数码管时钟程序直接使用,p3.2,p3.3,p3.4,p3.5 四键控制！实测24小时误差5秒。-Practical electronic clock, nixie tube clock for the six programs used directly, p3.2, p3.3, p3.4, p3.5 four key control! Measured 24-hour error of 5 seconds.

PIC16F72的2路AD程序，是用的WPS 文件保存的，请注意！-PIC16F72

使用MEGA16芯片，通过串口控制GSM模块，进行GSM模块配置，可以实现收发英文短信。当接受到相应短信可以自动反馈信息。编译环境为CVAVR-Use MEGA16 chip, through the serial port control of GSM module, GSM module to configure, you can achieve the send and receive SMS in English. When messages can automatically receive the appropriate feedback. Compile the environment CVAVR

嵌入式设计应用范例系列一。-embedded design a series of application examples.

使用DSP2812开发板进行AD转换的实例。该实例通过EVA启动AD转换，结果储存在AdcRegs.RESULTX寄存器中，结果为Q30格式。切记输入电压需调理至0-3 V之间，否则会烧坏DSP。

通常的汉字显示方式是先根据所需要的汉字提取汉字点阵（如16×16点阵），将点阵文件存入ROM，形成新的汉字编码；而在使用时刚需要先根据新的汉字编码组成语句，再由MCU根据新编码提取相应的点阵进行汉字显示。在这种显示方式中，如果使用的流字数量较大或语句较多时，利用汉字的新编码组成语句将是一件十分繁琐而枯燥的工作。针对这种情况，本文提出了一种十分简单的方式――直接利用PC机的汉字内码作为单片机系统的编码。-Chinese characters are usually displayed in accordance with the need to first extract of the Chinese character dot-matrix (such as 16 × 16 dot matrix), will be deposited into the matrix documents ROM, a new Chinese character encoding while just need to use the Chinese characters according to the new code composed of statements, and then by the MCU according to the new code to extract the corresponding Chinese character dot-matrix display. In this show the way, if you use the word flow statement number of the larger or more, the use of Chinese characters composed of a new coding language will be a very tedious and boring work. In view of this situation, this paper presents a very simple way- direct access to PC-code character encoding as a single-chip microcomputer system.

软件传输流解复用器。有益的各种嵌入式应用程序模拟 API 测试/模拟之前将其移植到实际硬件 h/w 解复用器......

应用背景The leading developers of Marlin are currently (January 2015) EvdZ and bkubicek, though many others contribute with their patches. This is a firmware for reprap single-processor electronics setups. It also works on the Ultimaker PCB. It supports printing from SD card+Folders, and look-ahead trajectory planning. This work is licensed under the GNU GPL v3 or (at the user"s discretion) any later version. It is based on Sprinter firmware, which was licensed under GPL v2 or later.关键技术 Features: Interrupt based movement with real linear acceleration. High steprate. Look ahead (Keep the speed high when possible. High cornering speed). Interrupt based temperature protection. preliminary sup