基于单片机的波形发生器源代码,可供代价参考交流

基于avr单片机的直流电机PID控制程序，工程文件的编译环境采用gcc for avr，可以在AVR Studio环境下调试，对电机开发人员具有参考价值。-avr microcontroller based on the DC motor PID control procedures, Project documents using gcc compiler environment for avr, the AVR Studio debugging environment, Development of motor officers with reference value.

SST39VF080 FLASH的单片机驱动源代码，可直接复制到uVision中验证，开发的单片机芯片为80C51-SST39VF080 FLASH microcontroller-driven source code, can be directly copied to verify uVision to develop chips for the 80C51 microcontroller

=== =时钟20:6=== === == 应先初始化状态寄存器 tx1714 EQU 7FFH PA EQU 05H PB EQU 06H PC EQU 07H PD EQU 20H IAR EQU 00H 间接寻址寄存器 TMR0 EQU 01H 定时器 STATUS EQU 03H 状态寄存器 BSR EQU 04H bank选择寄存器 PORTA EQU 05H I/0端口寄存器 PORTB EQU 06H I/0端口寄存器 PORTC EQU 07H I/0端口寄存器 PORTD EQU 20H I/0端口寄存器 PULL EQU 21H PULL-High上拉寄存器 WAKEUP EQU 22H 唤醒控制寄存器－－被用来设定watchdog允许和禁止 IRQM EQU 23H 中断屏蔽寄存器 IRQF EQU 24H 中断标志寄存器 WDTSEL EQU 25H -=== === = clock 20 : 6 === === === == should first register initialization state tx1714 EQU 7FFH EQU PA PB EQU 05H 06H 07H PC EQU PD EQU 20H IAR E QU 00H indirectly addressable registers TMR0 EQU 01H timer STATUS EQU Mr send state BSR EQU-deposit bank in the 04H choice Register PORTA EQU 05H I/O ports Register P ORTB EQU 06H I/O ports Register PORTC EQU 07H I/O ports Register POR TD EQU 20H I/O ports Register PULL EQU 21H PULL-High pull Register WAKEUP EQU 22H awaken control registers-- were used to set watchdog allowed and prohi

本文件中包括了几乎所有的常见封装尺寸，对PCB制作很有帮助-this document, including almost all of the common package size, the PCB production helpful

SAMSUNG S3C6410 CPU BSP for winmobile6-SAMSUNG S3C6410 CPU BSP for winmobile6

采用UART方式0与LM74通信。 用C8051f020的P0.7作片选，主机通过TXD发送时钟信号，实现同步通信,半双工.RXD 作双向数据线.用六位数码管显示LM74采集的温度值-The use of UART communication mode 0 and LM74. P0.7 used for the C8051F020 chip select, host TXD sent through the clock signal, to achieve synchronous communication, half-duplex. RXD for bi-directional data line. With six digital tube display LM74 temperature collected

atmega16开发板、Proteus、原理图-ATmega16 development board, Proteus, schematic diagram

目的 : 建立方便的LCD162操作子程序 目标系统: 基于任何兼容C51的微处理器 应用软件: Keil C 版本 : Version 1.0 LCD162程序-Objective : To establish a convenient target subroutine LCD162 operating system : C51 on any compatible microprocessor applications : Keil C version : Version 1.0 LCD162 procedures

TLC2543驱动程序-TLC2543 driver