基于单片机的无线遥控系统，这是本人精心制作的课程设计，花了将近一个月的时间才完成的。里边有具体的程序代码，全都是仿真通过，并且做出了pcb板，经得起考验的-Based on single-chip wireless remote control system, This is my elaborate curriculum design, has spent nearly a month before the finish. Inside there is a specific code, all the simulation are passed, and made a pcb board, stand the test of

MSP-FET430X110 C语言例子程序-MSP-FET430X110 C language examples procedures

单片机的24C02读写程序,使用Keil c编译器测试正常。-the 24C02 microcontroller literacy, the use of Keil c compiler tests are normal.

C8051FO6X系列的单片手册本书为中文叙述详解-Series of single-chip C8051FO6X manual for the English description of the book explain

DS18B20芯片资料（英文），有需要的朋友请下载！-DS18B20 chip data (English), there is a need to download the Friend!

proteus经典著作,最全库文件,图形液晶模块驱动芯片-proteus classics, most complete library files, graphic LCD Module Driver IC

1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.

英飞凌16位单片机XC164CS的TWINCAN应用资料，很详细，非常好用-Infineon 16-bit single-chip XC164CS TwinCAN application of information, very detailed, very easy to use

功能： 1、作为下位机采集8255数据并将此数据通过通讯送出， 2、采集数据为BCD，先转换成二进制，处理后再转换成BCD 3、通讯采用方式3，多机通讯，上位机发地址时TB8=1，其他TB8=0 下位机SM2=1，RB8=1时产生中断后使SM2=0收发数据，结束后SM2=1-Features: 1, as under the 8255-bit machine data collection and communications sent through this data, 2, collected data for the BCD, first converted into binary, and then converted to deal with BCD 3, communication using methods 3, multi-machine communication, PC-fat address TB8 = 1, other TB8 = 0 under the digital machine SM2 = 1, RB8 = 1 when the failure to make SM2 = 0 to send and receive data, after the end of SM2 = 1

用于cml860芯片收发DTMF和FSK信号-Cml860 for DTMF and FSK transceiver chip signal