The driver of C8051, it will bring you very big benfit if you will read it, it i...

ART OF Assembly Language Programming, 很不错，可惜我没有时间看-ART OF Assembly Language Programming, very good, but I have no time to read

masm32菜单使用的例子-masm32 menu use example

c和c++代码精粹，这是一个pdg格式的文档，请使用超星的最新版本打开，很难得的文档，是vip会员的资料，先睹为快吧:)-c and c++ code essence, this is a PDG format document, please use the latest version of Chaoxing open, it is difficult to get the documents, is vip membership information, preview it:)

(中断子程序)计时子程序----------------ＣＬＯＣＫ 功能：①TMR1每50000指令周期(即50000微秒)中断一次, 进入本程序后重装定时器 TMR1, 并清除TMR1溢出标志(PIR1,0). -(Interrupt Subroutine) subroutine CLOCK timing functions: ① TMR1 every 50000 instruction cycles (that is 50000 microseconds) disruption of the first to enter this process re-timer TMR1, and clear TMR1 overflow flag (PIR1, 0).

功能最全的能够运行四则运算的计算器且利用堆栈实现带括号的功能-The most versatile able to run the calculator and the four operations with the use of the stack to achieve the function in parentheses

设计一种自动洗衣机的程序控制器，在启动后先进水，等到达高水位后，启动洗衣马达转动4min，如在洗衣过程中发现水位低于高水位，则停止洗衣马达转动并报警，并在水位到达高水位后再次启动马达。洗衣结束后则启动排水开关，待水位到达低水位后，则启动脱水马达，转动2min。如此重复三次，要求在每一动作之间有2s的间隔。 高水位，低水位为水位传感器，用两个开关模拟，当水位高于高水位或低于低水位时，两个开关的状态分别为0 。启动开关用一个开关表示。进水、排水、洗衣马达、脱水马达及报警分别用一个发光二极管表示。本实验只需用可编程并行接口电路的A口。其硬件接口如下图所示。也可采用可编程逻辑器件进行设计。 -Design of an automatic washing process controller, after commencement of advanced water, and so on to reach the high water mark, start laundry motor rotation 4min, such as in laundry water level lower than that found during the high water mark, then the motor stops rotating laundry and alarm, and the the water level reaches the high water mark again to start the motor. Laundry is started after the end of the drainage switch, when the water level reaches the low water level, then start the dehydration motors, rotating 2min. Repeat three times, each action requires the interval between the 2s. High water, low water level as water level sensors, with two analog switches, when the water

是有线系统的发送程序，用汇编的，希望对大家有用。-Cable system is to send a program, compiled with the hope that useful to everyone.

用LabVIEW做的钟表和计时器。可以自动记录时间到txt文件中-LabVIEW to do with clocks and timers. Can be automatically recorded time to txt file

硬件试验的源代码，和好-hardware test source code, and good