编程爱好者，自编C程序跑灯，控制单片机P1口，逐个点亮心中的明灯...

profibus 的官方文件，朋友给的，朋友可是花钱买来的。-PROFIBUS_DP SPECIFICATION

STM32 I2C 例程，开发环境为KEIL for arm,并带Proteus仿真-STM32 I2C routines

美国TI公司的protel 元器件库，在应用中需要更新，本人收集了最新的版本共30M，为提高上传速度分六次上传。文件名依次为TI_1到TI_6。希望大家设计电路板时少走弯路这里是第二个TI-2-TI" s U.S. Treasury protel components, need to be updated in the application, I collected a total of up-to-date version of 30M, to improve the upload speed upload six hours. File name followed by TI_1 to TI_6. Hope that the design of circuit board less detours here is the second TI-2

CAN三台机子互相通讯（机子2程序），已调通，标准的标识符，11位。-CAN communication with each other three loom (loom 2 procedure), Qualcomm has been transferred, the standard identifier, 11.

使用VB编写的上机位的串口控制,我的串口搞定与大家一起分享快乐.上位机是用VB编的. 我想告诉大家是:其实串口通信也不是什么很难的事,只要用心去搞一定能作好的. -VB prepared on the use of machine-bit serial control, serial port I get to share their happiness with you all. PC is VB series. I want to tell you is: In fact, serial communication is not a difficult thing, as long as intentions to engage in will certainly be able to prepare for.

液晶显示模块。在lcd上显示数字的函数。-display of the lcd

Philips单片机P89C51RD和西门子Profibus工业总线的接口程序,硬件是鼎实公司的实验板,使用的鼎实公司的总线桥.-Siemens Profibus and Industrial Access Bus export procedures, hardware Teijitsu board of the company, using the company"s Teijitsu Bus Bridge.

C8051F020的头文件，主要是本单片机的硬件地址指向等。-C8051F020 the first document, is the MCU hardware addresses at the other.

基于51系列的电子锁设计方案，包含程序，pdf文件-Based on the 51 series of electronic lock design options, including procedures, pdf file

利用动态扫描和定时器1在数码管上显示 出从765432开始以1/10秒的速度往下递减 直至765398并保持显示此数，与此同时利 用定时器0以500MS速度进行流水灯从上至 下移动，当数码管上数减到停止时，实验 板上流水灯也停止然后全部开始闪烁，3秒 后（用T0定时）流水灯全部关闭、数码管上 显示出"HELLO"。到此保持住。 设晶振频率为12MHz。-The use of dynamic scanning and Timer 1 in the digital control to show from the beginning of 765,432 to 1/10 seconds until the speed of descending down 765,398 and maintain display this number, at the same time the use of Timer 0 to 500ms the speed of light from the flowing water to Under the move, when reduced to a few digital tube stop, the experiment on-board water stop and then all the lights started to flicker, 3 seconds later (T0 regularly used) closed water lights, digital tubes show