44780下51单

使用AT89C2051的红处遥控窗帘 作者：徐福成 　　本文介绍一款使用微电脑管理的、红外遥控器控制的多功能窗帘控制器。该窗帘控制器采用 89C2051 单片机的最小系统设计，控制一个 220V 的可逆、变速电动机控制窗帘的拉开和关闭。 　　窗帘控制器可以使用红外遥控器进行远程手动开、手动关和手动停控制；可以执行事先输入的开启时间和关闭时间进行时间控制；还可以根据室外环境亮度实现环境亮度光控。三种工作方式可以方便地进行选择，当选择时间控制的方案时，数码管还能显示当时小时和分钟时间，不过时间数据只能顺序显示，显示一遍后，略等片刻再显示下一遍时间。另外、电机拉动窗帘的工作的时间长度，电机工作的时候是否有鸣响提示，以及光控状态下环境亮度的控制参数的调整等等都可以通过遥控器进行设置。-use of the red remote control curtain Department Author : Xu cost of introducing the new management of the use of microcomputer, infrared remote control of the multi-function controller curtains. The curtain controller 89C2051 the minimum system design, control of a 220V reversible, variable speed motor control and opened the curtains closed. Curtain controller can use infrared remote control for remote manual open, manual clearance and stopped manually control; Input can be implemented prior to the opening time and the closing time to time control; Also under the outdoor environment can achieve environmental brightness optical brightness control. T

具体的硬件结构,大家可以看 WS 系列产品的原理图 * 利用AT89S51单片机来制作一个手动计数器，在AT89S51单片机的P3.3管脚接一个轻触开关， * 作为手动计数的按钮. 数码管驱动采用动态扫描方式用单片机的P0.0－P0.7驱动数码管的段码， * P1.3 控制个位数码管的共阳极公共端，P1.2 控制十位数码管的共阳极公共端 * 通过按一下P3.3按键,数码管做 1 的累加, 实现00~99的计数功能,当计到99时又从00开始. * 大家可自行修改程序,扩展到0000~9999的计数范围-Specific hardware architecture, we can look WS schematic family of products using AT89S51* Single-chip to produce a manual counter, in the P3.3 pin MCU AT89S51 by one touch switch,* as a manual count of button. nixie tube driven by dynamic scanning with MCU P0.0-P0.7 driver code segment digital tube,* P1.3 control bit digital tube anode of a total public client, P1.2 control of 10 digital total anode tube through public client* P3.3 click buttons, a digital pipe to do one of the cumulative, realize 00 ~ 99 count function, when the total to 99 from 00 the beginning of time.* everyone can modify the program, extended to 0000 range of ~ 9999 count

利用动态扫描和定时器1在数码管上显示 出从765432开始以1/10秒的速度往下递减 直至765398并保持显示此数，与此同时利 用定时器0以500MS速度进行流水灯从上至 下移动，当数码管上数减到停止时，实验 板上流水灯也停止然后全部开始闪烁，3秒 后（用T0定时）流水灯全部关闭、数码管上 显示出"HELLO"。到此保持住。 设晶振频率为12MHz。-The use of dynamic scanning and Timer 1 in the digital control to show from the beginning of 765,432 to 1/10 seconds until the speed of descending down 765,398 and maintain display this number, at the same time the use of Timer 0 to 500ms the speed of light from the flowing water to Under the move, when reduced to a few digital tube stop, the experiment on-board water stop and then all the lights started to flicker, 3 seconds later (T0 regularly used) closed water lights, digital tubes show

lcd keyboard example

三位半数字电压表程序，能测量-5~+5V电压，比较准确。-Three semi-digital voltage meter procedures to measure-5 ~+5 V voltage, more accurate.

18B20掼51掼keil显示，温度还没调试好就调试好，只要一点点就行

060资料,初级学生可以看看！学习060单片机-060book

一个keil c 写的一个点阵的程序，感觉还不错-Keil c Writing a lattice of a procedure, I feel pretty good

这是一个12864的汉字显示程序，是用C语言写的，是一个三级菜单。zhanggang-This is a 12864 Chinese characters display program, is written in C language, is a three-tier menu. zhanggang

基于单片机的频率采集、计数以及显示程序,具有广泛的作用~-The frequency of single-chip based on the collection, counting and display procedures, the role of a broad ~