-
船舶运动可视化仿真平台
此范例说明 了在LABVIEW平台下进行船舶运动可视化仿真平台(This example illustrates the ship motion visualization simulation platform in LABVIEW platform)
- 2020-06-22 21:00:01下载
- 积分:1
-
EMD的labview实现
EMD的labview实现,用纯labview语言编写(An EMD toolbox for labview)
- 2020-11-11 19:39:45下载
- 积分:1
-
resonant-frequency-testing
通过labview控制信号发生器和锁相放大器进行共振频率检测的程序。freq test.vi实现信号发生器的频率扫描,lockin test.vi 实现锁相放大器的参数设定,数据采集.vi实现锁相数据的采集,waveform arrays to file实现波形数据到文件数据的转换。共振频率测试.vi实现晶振等共振频率的测试(Resonance frequency detection procedures performed by labview control signal generator and lock-in amplifier. freq test.vi achieve frequency sweep signal generator, lockin test.vi setting parameters to achieve lock-in amplifier, a data acquisition. vi achieve phase lock data acquisition, waveform arrays to file converted waveform data to achieve document data. The resonance frequency of the test. Vi achieve crystal and other resonant frequency test)
- 2014-03-10 14:21:01下载
- 积分:1
-
labview
电感,电容,电阻的8个小程序,供初学者学习的好代码(Inductors, capacitors, resistors 8 small programs for beginners to learn the code of good)
- 2011-08-14 16:54:59下载
- 积分:1
-
AD9833LabVIEW
使用LabVIEW实现了DDS芯片AD9833的编程助手的功能,输入晶振频率和想要的输出频率即可得到控制字。很方便编程。(Using LabVIEW to implement the function of the DDS chip AD9833 s programming assistant, you can get the control word by typing the oscillator frequency and the desired output frequency. It s easy to program.
)
- 2017-05-06 10:37:57下载
- 积分:1
-
cisens
天窗检测上位机,与PLC通讯,检测天窗防夹力,遭遇等(NVH destination,Noise test and so on)
- 2018-01-02 16:17:50下载
- 积分:1
-
Hilbert
基于labview8.6的希尔伯特变换高精度测量低信噪比条件下两路正弦波相位差(Labview8.6 based Hilbert transform high-precision measurement of the sine wave phase difference of the two low SNR)
- 2013-03-16 18:56:55下载
- 积分:1
-
TEMP
说明: LABVIEW,温度计演示程序,学习用小程序(temperature programe)
- 2021-03-23 19:39:15下载
- 积分:1
-
TCP客户端程序
基于labview的TCP客户端程序发送主机通常将发送缓冲区中的数据按内存地址从低到?的顺序发出,接收主机把从?络上接到的字节依次保存在接收缓冲区中,也是按内存地址从低到?的顺序保存。
TCP/IP协议规定,?络数据流应采??端字节序,即低地址?字节。
socket API是?层抽象的?络编程接?,适?于各种底层?络协议,如IPv4、 IPv6,以及后?要讲的UNIX Domain Socket。(Based on the TCP client program to send the host LabVIEW will usually send buffer according to the data in the memory address from low to order issued, the receiving host to receive from the network bytes on sequentially stored in the receive buffer, and according to the memory address from low to preservation order.
The TCP/IP agreement, network data flow should be endian, low byte address.
Socket API is layer abstract network programming interface, suitable in various underlying network protocol, such as IPv4, IPv6, and UNIX Domain Socket to say.)
- 2018-01-15 01:19:31下载
- 积分:1
-
LS
little projects in lab view so i can just have access to downloads
- 2014-01-19 19:45:40下载
- 积分:1