美国TI公司的protel 元器件库，在应用中需要更新，本人收集了最新的版本共30M，为提高上传速度分六次上传。文件名依次为TI_1到TI_6。希望大家设计电路...

Generic_8052_ISD51源码,仿真器代码!想DIY 仿真器的有福了-Generic_8052_ISD51 source, Simulator code! DIY simulator to the blessed

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

AVR单片机下的mmc卡控制程序，包括系统SPI模式初始化，使卡进入SPI模式及检测等-AVR cards under the VAT control procedures, including the systematic SPI mode initialization, access cards and SPI mode detection

鼠标应用程序示范 MCU AT89S51 XAL 12MHz 本程序可以实现鼠标的功能,并将位置显示在LCD上-Mouse model application MCU AT89S51 XAL 12MHz mouse in this program can realize the function, and location displayed on the LCD on

AVR单片机六路ADC采集与七段数码管显示采集值-AVR Singlechip Lioulu ADC Acquisition and Seven-Segment LED display acquisition value

一个高速单片机的超声波测距的例子，本例程使用的广茂达能力风暴机器人的超声测距卡。-a high-speed microcontroller Ultrasonic Ranging example, the routine use of the ability to Guangmao turmoil robot Ultrasonic Ranging cards.

串行DA MAX517测试程序,测试通过，用示波器观察输出3.88V电压。

基于80C51单片机源码公开的Small RTOS 1.12.1版-80C51 microcontroller based on the open source version 1.12.1 Small RTOS

430成都技术培训会代码，使用IAR-4.10打开。-430 technical training in Chengdu will be the code, the use of IAR-4.10 open.

用protues简单制作的4X4键盘,有图和原程序,可实现按下键显示对应的数值-Protues produced using a simple 4X4 keyboard, there are maps and the original procedure, can be pressed to display the corresponding numerical